Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Steve68

Pages: [1] 2 3 ... 35
1
Maintenance / Re: At a loss - engine stalls under load
« on: July 05, 2022, 12:28:02 AM »
How did you check the fuel bowl levels?

2
Maintenance / Re: At a loss - engine stalls under load
« on: July 04, 2022, 09:10:09 PM »
Float level is good in both bowls. 
How do you tell if accel pump is functioning correctly?

Engine off. Remove carb cleaner. Look down carb throat. Use a light to light up area in throat if you can’t see clearly. Hold the throttle linkage in you hand and as you look down carb move the throttle as if accelerating, there should be a discharge (squirt) of gas into the throttle body area.  If you don’t see gas coming out during the throttle movement then there is an issue and likely your problem.

Use a service manual or Google to see how to set the correct spacing between linkage and pump lever.

3
Maintenance / Re: At a loss - engine stalls under load
« on: July 04, 2022, 06:53:56 PM »
Have you checked the float levels and other carb adjustments such as the accelerator pump?

4
Garage Talk / Re: Flux Capacitor
« on: May 28, 2017, 02:54:33 PM »
It's my understanding that they have/had this in their db so that if someone hacked them and used it as their own that O'Reillies would be able to prove they stole it.


Steve

5
Restoration / Re: Where to by correct master cylinder?
« on: November 15, 2016, 03:00:09 AM »
The lack of RPV's in aftermarket cylinders was discussed in the following thread in 2007.  http://www.camaros.org/forum/index.php?topic=2938.msg18849#msg18849

Steve

6
General Discussion / Re: 68 Trunk Mat
« on: September 07, 2015, 09:21:10 PM »
Yep. :(

8
General Discussion / Re: 68 Trunk Mat
« on: September 07, 2015, 08:25:52 PM »
Darrell

If the mat is sill out of he car flip it over and see what the part number is......just curious. 

Steve

9
Originality / Re: 67 68 Camaro manual drum brakes
« on: March 26, 2015, 11:45:21 PM »
Question: you are sure the rear drum brakes are actually working with the RPV out?  If they are then there must be some residual pressure there somewhere if you don't notice any nose dive or have a longer pedal travel than normal.  How far does the pedal travel before you get rear brakes to engage?  Have the lines to the rear been replaced to your knowledge?  How about the switch assembly (right under the master cylinder).....has it been replaced or is it the original?  Any possibility either may have some buildup in them?  You bled something, was it the master or at the rear wheel cylinders?  I suppose if there is some restriction and since the master is higher than the rear cylinders there might be enough head pressure to keep the cylinders out but I sure wouldn't want to rely on that.

Steve

10
Restoration / Re: 67 camaro master cylinder
« on: February 04, 2015, 03:12:02 AM »
You mean the RPV.  Sure, you would just pull the brass seat and put it in.  You would need to install a spring as well under the RPV and a new seat.

Steve

11
Restoration / Re: 67 camaro master cylinder
« on: February 04, 2015, 02:59:22 AM »
Bc69

I was really responding to Kurt's comment. 

I believe any master cylinder port would need a RPV if that particular line was feeding a drum brake cylinder.  Necessary to keep some back pressure for it to work properly.

Steve

12
Restoration / Re: 67 camaro master cylinder
« on: February 04, 2015, 02:31:02 AM »
That's all on the site at: http://www.camaros.org/suspen.shtml#Brakecomp

Yea, that's what I said up front.  From the "Chassis/Brake System" report:

13
Maintenance / Re: Braking problem
« on: January 01, 2015, 02:53:17 AM »
Read these:  http://www.camaros.org/forum/index.php?topic=2938.0
and http://www.camaros.org/brakevalve.shtml

See if any of that info helps.

Steve

14
6-cylinder Camaros / Re: Key Plugs that came with my 68 L6
« on: November 25, 2014, 12:12:20 AM »
Still have mine from my 68.  I have them in the original paper pouch provided by the dealership.  Also,  one of my sons has a 67 that still has the plugs in the keys.

Steve

Pages: [1] 2 3 ... 35
anything