CRG Discussion Forum
Welcome, Guest. Please login or register.
Did you miss your activation email?
February 01, 2015, 07:21:38 PM

Login with username, password and session length
Search:     Advanced search
Welcome to the CRG Discussion Forum!
Forum registration problems: Make sure you enter your email correctly and you check your spam box first. *Then* email KurtS2@gmail for help.
109383 Posts in 12661 Topics by 4867 Members
Latest Member: 69z-x77
* Home Help Search Login Register
+  CRG Discussion Forum
|-+  Camaro Research Group Discussion
| |-+  Originality
| | |-+  Correct engine paint suggestions please!
« previous next »
Pages: 1 ... 3 4 [5] 6  All Print
Author Topic: Correct engine paint suggestions please!  (Read 8798 times)
JohnZ
CRG Member
*****
Posts: 4203


View Profile Email
« Reply #60 on: May 10, 2014, 09:04:10 AM »

Isn't that a water wall in front of them to act as an air filter?

Mike

It captures the overspray and contains it in a water-filled sump below the grated floor; there was a LOT of paint being sprayed at 300 engines per hour (one every 12 seconds).
Logged

'69 Z/28
Fathom Green
CRG
JoeC
Member
***
Posts: 355


View Profile Email
« Reply #61 on: May 14, 2014, 07:51:32 AM »

on engines like the Z/28 and L78 with alum intake and chrome or alum valve covers.
I know they used some type of cover or masking device to mask off the valve covers and intake that resulted in different levels of orange paint overspray but was the distributor covered?

Did the distributor get any orange paint on a 302 Z or L78 engine and would the dist on an slum intake engine look different then an iron intake engine?

I have an unrestored 499 L78 L72 distributor and has no paint on it

Logged
JohnZ
CRG Member
*****
Posts: 4203


View Profile Email
« Reply #62 on: May 14, 2014, 11:01:55 AM »

on engines like the Z/28 and L78 with alum intake and chrome or alum valve covers.
I know they used some type of cover or masking device to mask off the valve covers and intake that resulted in different levels of orange paint overspray but was the distributor covered?

Did the distributor get any orange paint on a 302 Z or L78 engine and would the dist on an slum intake engine look different then an iron intake engine?

I have an unrestored 499 L78 L72 distributor and has no paint on it



The distributor was masked with a high-tech device (a coffee can) - the hold-down clamp portion of the housing sometimes had orange overspray, sometimes it didn't.
Logged

'69 Z/28
Fathom Green
CRG
JoeC
Member
***
Posts: 355


View Profile Email
« Reply #63 on: May 16, 2014, 06:20:36 AM »

John , thanks for the reply

was this coffee can mask process the same for aluminum intake engines and iron intake engines?

Do you recall what was used to mask off the aluminum intake and alu/chrome valve covers of the L78s and 302 Z engines?

Logged
JohnZ
CRG Member
*****
Posts: 4203


View Profile Email
« Reply #64 on: May 16, 2014, 10:10:44 AM »

John , thanks for the reply

was this coffee can mask process the same for aluminum intake engines and iron intake engines?

Do you recall what was used to mask off the aluminum intake and alu/chrome valve covers of the L78s and 302 Z engines?



Coffee cans were used to mask the distributor all engines.

Aluminum intakes and aluminum or chrome valve covers were covered with vacuum-formed plastic masks the engine plants made in their toolrooms.
Logged

'69 Z/28
Fathom Green
CRG
Mike S
Hero Member
*****
Posts: 1215



View Profile
« Reply #65 on: May 16, 2014, 10:32:40 AM »

 John, serious about real coffee cans? Were the distributors timed and locked down by that time?
Was the distributor cap on too during the spraying process?
Heck, if it was a real can I'll use a Maxwell House can and replicate the process when I respray my block again.

Mike
Logged

67 LOS SS/RS L35 Hardtop - Original w/UOIT
67 NOR SS/RS L35 Convertible - Restored
JohnZ
CRG Member
*****
Posts: 4203


View Profile Email
« Reply #66 on: May 17, 2014, 11:00:31 AM »

John, serious about real coffee cans? Were the distributors timed and locked down by that time?
Was the distributor cap on too during the spraying process?
Heck, if it was a real can I'll use a Maxwell House can and replicate the process when I respray my block again.

Mike

Yup, coffee cans. The distributors came from Delco-Remy without the caps - the caps were installed right after the distributor was installed on the engne. The distributor was locked down later, when the timing was set during hot-test. The hot-test stands included a slave quick-connect ignition/plug wire harness and slave exhaust manifolds.
Logged

'69 Z/28
Fathom Green
CRG
6667ss138
Member
***
Posts: 303


View Profile
« Reply #67 on: May 17, 2014, 11:10:15 AM »

Very interesting stuff JohnZ. Your first hand knowledge and willingness to share is awesome and very much appreciated! So much to learn here. Wish I would have found this site years ago.
Logged

Len H.  Kansas
1969 07A X77D80 Hugger Orange/Black Vinyl Top, complete 3 owner history
1967 Chevelle SS396 138 Convertible/Red/Black int.
1966 Chevelle SS396 138 4sp California/Smog/Black/Red int. POP, original CA black plates
My68SS
Member
***
Posts: 350



View Profile
« Reply #68 on: May 26, 2014, 10:27:42 AM »

+1
The photo's and info in this thread are pure gold!! Thanks JohnZ and everyone else for contributing  Smiley
Logged

Rob
1968 L34/M40 SS
12 bolt posi 3.55
Build - 12C
6667ss138
Member
***
Posts: 303


View Profile
« Reply #69 on: December 30, 2014, 10:48:49 PM »

You guys were gracious enough when I first asked this question to offer many great suggestions. I thought I would show what I decided to use for the engine color paint on my 66 big block. I thought some might find it interesting that we found the 69 Hugger Orange color matched almost spot on with my bracket which is an early take off survivor, original paint, smog bracket(you can see the bracket before I stripped it sitting on top of the intake). My friend that owns a body shop came over to shoot it for me. He uses Glasurit paint at his shop. I decided to not go with a complete exhaust manifold overspray, even though I do agree that is how it was originally done at Tonawanda. Thanks again for all the help!
Logged

Len H.  Kansas
1969 07A X77D80 Hugger Orange/Black Vinyl Top, complete 3 owner history
1967 Chevelle SS396 138 Convertible/Red/Black int.
1966 Chevelle SS396 138 4sp California/Smog/Black/Red int. POP, original CA black plates
NoYenko
Member
***
Posts: 329



View Profile
« Reply #70 on: January 02, 2015, 08:52:48 AM »

Len, Your engine looks great. I like that the paint finish appears to be a little flatter, less glossy, than what you typically see. I was going to use a chemical to dull the fresh paint on my engine but decided not to experiment on it. Good job. George
Logged
69Z28-RS
Hero Member
*****
Posts: 2683


owner since '76


View Profile Email
« Reply #71 on: January 02, 2015, 10:20:11 AM »


.....  AND...    Hugger Orange goes good on anything..  Smiley   

Happy 2015 everyone.  Hopefully this year will be the best yet for all of us here.. and for our world...
Logged

Gary W.  /  69Z28-RS, 72 B 720 cowl console rosewood all tint
69 Corvette convertible, silver/black 350 hp,
60 Corvette white/red, 72 Corvette coupe (2), 
90 ZR1 red/red #246, 90 ZR1 white/gray #2466
72 El Camino, '55 Nomad, '57 Nomad, '57 B/A Sedan
6667ss138
Member
***
Posts: 303


View Profile
« Reply #72 on: January 02, 2015, 11:03:55 AM »

Thank you George, and yes Gary it sure does  Smiley
Happy New Year!
Logged

Len H.  Kansas
1969 07A X77D80 Hugger Orange/Black Vinyl Top, complete 3 owner history
1967 Chevelle SS396 138 Convertible/Red/Black int.
1966 Chevelle SS396 138 4sp California/Smog/Black/Red int. POP, original CA black plates
My68SS
Member
***
Posts: 350



View Profile
« Reply #73 on: January 08, 2015, 12:30:10 PM »

...we found the 69 Hugger Orange color matched almost spot on ....
Very interesting. Here in Au my brother and I used GM-H Sebring Orange, a color used on '69 Monaro's and Torana's.
It too is a very close match like the Hugger Orange.
Did he add a flattener to the Glasurit paint? Looks good!  Smiley
Logged

Rob
1968 L34/M40 SS
12 bolt posi 3.55
Build - 12C
cook_dw
Hero Member
*****
Posts: 1055



View Profile Email
« Reply #74 on: January 08, 2015, 02:41:58 PM »

Right or wrong this is how mine turned out.  I painted it this past Sunday.





Logged

Darrell Cook

1967 LeMans Blue SS/RS L35 clone
1968 Rallye Green SS L78 - unrestored original
1968 Matador Red Z28
Pages: 1 ... 3 4 [5] 6  All Print 
« previous next »
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.20 | SMF © 2013, Simple Machines Valid XHTML 1.0! Valid CSS!
Page created in 0.078 seconds with 18 queries.