Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - BillOhio

Pages: 1 ... 74 75 [76] 77 78 79
Restoration / Re: springs on 69z
« on: August 31, 2012, 10:36:49 PM »
I did some measuring and the springs hbc sells for a small block are not z springs! My car is almost 3 inches higher than it should be. I kid you not it looks like the engine is out. From what i have found, i need the moog part 6803. Of course i have a show in my home town town at our fair and i hope we get rain so i can leave it home. Really disgusted with hbc after they talked me out of an nos set they hadz and then sold me these. The set they have is 6312, and its not even the 2nd choice for a z

General Discussion / Re: Introduce myself an my car
« on: August 28, 2012, 06:39:03 PM »
If that car didn't work out, i have seen some nice camaros on Ebay and i think on in Florida recently.

Restoration / Re: springs on 69z
« on: August 28, 2012, 01:48:14 AM »
My car had a yf tag on the spring we took off. What is really annoying, one side is 3/4 inch higher than the other!

Restoration / Re: springs on 69z
« on: August 27, 2012, 09:15:24 PM »
Was looking at a chart in the classic industries book and they show the 6 cylinder coupe using the same coil  spring as a z. Might drop mine down a bit

Restoration / springs on 69z
« on: August 27, 2012, 06:34:00 PM »
Just had my front springs replaced and the moog ones from HBC were 2 coils higher. Car doesn't sit where it should. No one is selling the specific ones anymore so these were genetic  for small block, no air. anyone have better luck? Also appears the back springs are sagging. anyone  tried to rearch them?

Decoding/Numbers / Re: ebay unrestored z
« on: August 27, 2012, 04:19:31 AM »
Noticed it has hood insulation and trunk mat. Weren't those only for deluxe interiors?

Decoding/Numbers / ebay unrestored z
« on: August 26, 2012, 06:05:15 PM »

hope I got all  the link, it goes off today. After seeing a "survivor" with a replaced block, wrong heater hoses and several other suspectable things, I saw this car and it is unrestored but repainted and has picture of block on engine stand. Gosh whats left that hasnt been restored?? 

Originality / Re: 69 Z/28 metal vacuum line correct?
« on: August 20, 2012, 03:34:38 PM »
is there any paint on this clip on a z? One I bought has orange on it but might be off a painted manifold

Originality / Re: Picture of 69 z top of engine wanted
« on: August 15, 2012, 02:45:10 AM »
Mine has tube and hose and pretty sure its the original hose. No clip. I did buy a used one and wondered why it has orange paint on it

Originality / Re: Picture of 69 z top of engine wanted
« on: August 13, 2012, 11:40:34 PM »
Maybe I am not missing any parts!  that would be good.
Thanks Paul

Originality / Re: Picture of 69 z top of engine wanted
« on: August 13, 2012, 11:10:51 PM »
thats what I was looking for but dont see the vacuum advance clip or the pcv bracket that goes on the carb bolt. anyone got any others?

Originality / Picture of 69 z top of engine wanted
« on: August 13, 2012, 10:04:29 PM »
I am trying to see what the passenger side of the carb area looks like and have not found a good picture. would someone post an original car please? I am trying to make sure I have all the right clips and brackets.

Restoration / Re: Paint gun....choosing the right one.
« on: August 11, 2012, 03:21:06 PM »
I am no expert but just purchased a gun from Eastwood that is on sale for a couple days. Their concours gun is supposed to work on a home compressor hvlp gun. Primer can be hard on a gun if you use it much so i will use a harbor cheap gun my buddy has. It really puts out material

Restoration / Re: fw wheels abd trim rings
« on: July 29, 2012, 10:01:03 PM »
I think I read about it on team camaro. 
Does anyone know if you can tell the repro from originals??

General Discussion / Re: 1969 Z28 Camaro
« on: July 29, 2012, 09:53:31 PM »

Pages: 1 ... 74 75 [76] 77 78 79