Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - ban617

Pages: [1] 2 3 ... 15
1
Decoding/Numbers / Re: 1969 Z28 Block ID
« on: August 06, 2022, 11:43:29 AM »
How do you know your engine in question has 4 bolt mains ? Have you had it apart ? If so does it have an 1178 crankshaft for a 302 ? Maybe the original engine was hurt & the original block was unusable, so they put the surviving pieces into this block in the car Ö

2
1969 - Orphans / Re: 69 DZ 302 V1I15DZ
« on: April 12, 2021, 11:30:02 PM »
If the VIN isnít on the pad wouldnít it be on the bell housing flange ?

3
General Discussion / Re: What Shocks Should I Use For A Smooth Ride ?
« on: April 12, 2021, 11:27:04 PM »
Make sure that your rear shackles arenít bound up or you will have a harsh ride .... Also if the shocks are too short in the rear it will ride harsh...

4
Restoration / Re: Painting details...
« on: March 22, 2020, 10:59:34 AM »
   Nice work as always... What products are you using for the suede like a factory mix or custom ? Also are you using the 3m Shutz for the undercoating?

Thanks

5
Restoration / Re: .030 over pistons for 302: specs/supplier?
« on: March 03, 2020, 06:43:06 AM »
Hi , with the Crower cam did you run roller rockers & a stud girdle or possibly a rev kit ?
Thanks

6
General Discussion / 1969 Original Battery Cables
« on: January 27, 2020, 08:56:32 PM »
  Hi , my project car still has itís original battery cables spring type for a top post battery , are the clamps available to crimp on the original cables ?
Thanks Rob

7
Originality / Re: Oil Pan and Windage Tray
« on: June 05, 2019, 04:38:11 PM »
On your pickup I have seen the weld crack when you try to weld the pickup to the pump ... I make a little sheetmetal bracket & weld it to the pickup & bolt it to the pump ...

8
General Discussion / Re: Firewall pad clarification
« on: June 05, 2019, 02:56:37 PM »
How does the quite ride  compare to the accurate reproduction?

9
1968 - Orphans / Re: 68 MO
« on: June 05, 2019, 02:52:41 PM »
Iíll get the casting date & pics of the pad....Iím 98% sure itís real the guy has probably had it for over 30 yrs.

10
1968 - Orphans / 68 MO - 124378N436166
« on: June 04, 2019, 02:41:59 AM »
Hi , I came across a 68 MO Block that will for sale ...
 
The build date is V05IIMO
  The Vin is 18N436166

11
Maintenance / Re: Posi additive in Australia
« on: May 10, 2019, 03:21:41 PM »
Most all the rear end line that I have seen has it ...

12
Maintenance / Re: Temp sending unit for a 69
« on: May 10, 2019, 03:20:35 PM »
 I replaced one years ago with a standard ignition brand & it seemed ok , never actually checked the temp .. But if your needle is really low can you adjust the needle? Iíve always wondered how the gauges were marked v/s actual degrees..Mine was lying to me & said it was boiling & it wasnít..

13
Ok ,on the alternator what about the voltage regulator was it the stock one or transistor ignition one ?

14
General Discussion / Re: 69 trim tag question
« on: March 21, 2019, 10:49:38 AM »
  What color was the car ? Looks like a - - which be nice to have

15
General Discussion / Re: Quick Question
« on: March 21, 2019, 10:27:42 AM »
 I just recently saw a GM fiberglass Crossram hood for sale & I believe it had the hood pins with an installation diagram , Canít recall if it also had the prop rod or not ... As far as buying a new hood Glasstek makes the hood that fits the Crossram air cleaner & itís probably cheaper than the normal Camaro parts houses..

Pages: [1] 2 3 ... 15