Author Topic: What is the correct finish on these fasteners please?  (Read 4408 times)

BlackoutSteve

  • Member
  • ***
  • Posts: 397
    • View Profile
What is the correct finish on these fasteners please?
« on: November 25, 2009, 07:53:38 AM »
1969 Camaro.
Screws that fasten the heater control panel in place. 3923905 UPC1 M5..
as well as the speedo, tach and center fuel gauge lenses.. (center fuel gauge is 3849634 RPO U17 A1)

www.amkproducts.com catalog shows them only in stainless. (2010 catalog Pg 81)
I thought they were painted black. Which is OE ?
Restoring my RHD 69 Jane in Melbourne, Australia.
http://www.usmuscle.com.au/Forum/showthread.php?t=2840

mark x22

  • Member
  • ***
  • Posts: 131
    • View Profile
Re: What is the correct finish on these fasteners please?
« Reply #1 on: November 25, 2009, 03:00:53 PM »
My clock screws are chrome , the speedo and tack are black . does the AIM show different numbers ?

JohnZ

  • CRG Member
  • *****
  • Posts: 4365
    • View Profile
Re: What is the correct finish on these fasteners please?
« Reply #2 on: November 25, 2009, 04:11:26 PM »
Mine has never been touched, and all of those bezel/cluster/heater control screws are black phosphate.
'69 Z/28
Fathom Green
CRG

BlackoutSteve

  • Member
  • ***
  • Posts: 397
    • View Profile
Re: What is the correct finish on these fasteners please?
« Reply #3 on: November 26, 2009, 07:59:11 AM »
Thanks John & Mark.. ;D

Mark, the AIM doesn't show the speedo & tach screws because I think those gauges in the instrument panel were already an assembly on the production line.. So I used the center fuel gauge numbers. I would assume they are all the same. ..I hope.

AMK only sell the 3849634 in stainless. (B-11117 pg 81). That's fine. I'll paint them unless thier S15 finish is a black finish. The pic almost looks like they're black.
Restoring my RHD 69 Jane in Melbourne, Australia.
http://www.usmuscle.com.au/Forum/showthread.php?t=2840

68Zproject

  • Hero Member
  • *****
  • Posts: 1868
    • View Profile
Re: What is the correct finish on these fasteners please?
« Reply #4 on: November 26, 2009, 03:40:34 PM »
S-15 is black oxide at AMK.
68Z28

BlackoutSteve

  • Member
  • ***
  • Posts: 397
    • View Profile
Re: What is the correct finish on these fasteners please?
« Reply #5 on: November 26, 2009, 06:34:04 PM »
Page 4.. Yep, it is too.. Thanks.  ;)
Restoring my RHD 69 Jane in Melbourne, Australia.
http://www.usmuscle.com.au/Forum/showthread.php?t=2840

sixt9x33rs

  • Hero Member
  • *****
  • Posts: 980
    • View Profile
Re: What is the correct finish on these fasteners please?
« Reply #6 on: November 30, 2009, 03:07:13 AM »
Mine has never been touched, and all of those bezel/cluster/heater control screws are black phosphate.

Mine are the same as John's.
'69 RS Z/28 65B, 711 Flat hood no spoiler, endura, 4:10 43K miles
69 X77 Z/28 69 69 711 Original Paint Unrestored (Sold)
'69 X66 Convertible 69B 712 auto, (Sold) 44K miles

 

anything