CRG Discussion Forum
Welcome, Guest. Please login or register.
Did you miss your activation email?
September 02, 2014, 09:09:35 AM

Login with username, password and session length
Search:     Advanced search
Welcome to the CRG Discussion Forum!
Forum registration problems: Make sure you enter your email correctly and you check your spam box first. *Then* email KurtS2@gmail for help.
103782 Posts in 12188 Topics by 4700 Members
Latest Member: lpetruc
* Home Help Search Login Register
+  CRG Discussion Forum
|-+  Camaro Research Group Discussion
| |-+  Restoration
| | |-+  pan gaskett
« previous next »
Pages: 1 [2]  All Print
Author Topic: pan gaskett  (Read 4720 times)
jeff68
Member
***
Posts: 349



View Profile
« Reply #15 on: December 17, 2011, 01:05:48 PM »

Thanks John & Todd.
John - Did you use your original hardware as well when installing this gasket on an original oil pan?
Logged

68 L30 / M20 Convertible
Ash Gold
TODD
Member
***
Posts: 73



View Profile
« Reply #16 on: December 17, 2011, 10:20:36 PM »

I do remeber the gasket has little plastic spacers for each bolt location, and you have to start at the end and work the pan down.
My pan is a GM rplacement part with large end gaps. The little plastic sleeves prevent over compression and consistant gasket unformity.
Good gasket, I also used felpros reusable timing gasket hard metal base with silicone face works well.

Todd
Logged
bc69
Member
***
Posts: 206



View Profile Email
« Reply #17 on: December 17, 2011, 10:36:26 PM »

Just purchased it, all hardware and retainers included just as in johnz's pic.
$25 at OReilly's
Logged

Brad
RSSS
bc69
Member
***
Posts: 206



View Profile Email
« Reply #18 on: December 17, 2011, 11:35:32 PM »

Has anybody ran into a 69 that has required the thick front gasket? I
have one that takes thick front and stick is on driver side. All if the engine seems to be original.
Logged

Brad
RSSS
JohnZ
CRG Member
*****
Posts: 4079


View Profile Email
« Reply #19 on: December 18, 2011, 01:57:55 PM »

Has anybody ran into a 69 that has required the thick front gasket? I
have one that takes thick front and stick is on driver side. All if the engine seems to be original.

If it requires the "thick" front seal, you have a Service replacement Z/28 oil pan manufactured after 1975 or a post-'75 production non-Z/28 oil pan.
Logged

'69 Z/28
Fathom Green
CRG
Dave69x33
Member
***
Posts: 346



View Profile Email
« Reply #20 on: January 13, 2012, 09:50:06 PM »

I recently rebuilt my 302 and used the Felpro 1-piece gasket. I cleaned it very well with lacquer thinner before painting the engine and paint does stick to the rubber.  Over time, some paint will peal from the gasket but this can be touch up.  I have done this twice and it works well and hides the blue gasket. 
Logged
68Zproject
Hero Member
*****
Posts: 1622



View Profile Email
« Reply #21 on: December 09, 2012, 04:51:13 PM »

I know this thread is a little past, but can you re-use the one- piece gasket described above?
Logged

68Z28
JohnZ
CRG Member
*****
Posts: 4079


View Profile Email
« Reply #22 on: December 10, 2012, 10:49:44 AM »

I know this thread is a little past, but can you re-use the one- piece gasket described above?

Yes, you can - that's why it was developed.
Logged

'69 Z/28
Fathom Green
CRG
zman1969
Member
***
Posts: 107



View Profile Email
« Reply #23 on: May 08, 2013, 04:31:56 PM »

updating old thread: I just used this 1pc pan and it did not come with bolts - just a FYI much better design than original 4 pc cork and rubber
Logged

Rich

69 RS/Z DZ302 Daytona bumble bee
69 T/A clone LS6/6sp
69 Nova SS 396
Pages: 1 [2]  All Print 
« previous next »
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.19 | SMF © 2013, Simple Machines Valid XHTML 1.0! Valid CSS!
Page created in 0.29 seconds with 18 queries.