Author Topic: Family survivor 69 Camaro  (Read 59574 times)

firstgenaddict

  • Hero Member
  • *****
  • Posts: 2882
  • caretaker of 1971 LT1's 11130 & 21783
    • View Profile
    • Groome Family Automobiles
Re: Family survivor 69 Camaro
« Reply #45 on: May 01, 2018, 07:45:51 PM »
I love the firewall... the grey on the top with the misted lemans blue is so PERFECT... VERY FEW PEOPLE reproduce or replicate this detail correctly. THEY PUT WAY TOO MUCH body color.

The double T on the drivers side is quite typical.
James
Collectin' Camaro's since "Only Rednecks drove them"
Current caretaker of 1971 LT1's - 11130 and 21783 Check out the Black 69 RS/Z28 45k mile Survivor and the Lemans Blue 69 Z 10D frame off...
https://plus.google.com/photos/112392262205377424364/albums?banner=pwa

camaronut

  • Hero Member
  • *****
  • Posts: 681
    • View Profile
Re: Family survivor 69 Camaro
« Reply #46 on: May 08, 2018, 04:00:19 PM »
Congrats and.....wow.  Takes guts....

Can you take a photo of the dash panel top?  Like to see what the "suede paint" looks like after all these years.  thanks!

gma_camaro

  • Member
  • ***
  • Posts: 38
    • View Profile
Re: Family survivor 69 Camaro
« Reply #47 on: May 10, 2018, 03:12:07 AM »
Sizes of firewall letters








Dash pictures did not look great under garage lights, will get some in daylight tomorrow.

firstgenaddict

  • Hero Member
  • *****
  • Posts: 2882
  • caretaker of 1971 LT1's 11130 & 21783
    • View Profile
    • Groome Family Automobiles
Re: Family survivor 69 Camaro
« Reply #48 on: May 11, 2018, 12:07:49 AM »
IS the Radiator Code UH?



James
Collectin' Camaro's since "Only Rednecks drove them"
Current caretaker of 1971 LT1's - 11130 and 21783 Check out the Black 69 RS/Z28 45k mile Survivor and the Lemans Blue 69 Z 10D frame off...
https://plus.google.com/photos/112392262205377424364/albums?banner=pwa

gma_camaro

  • Member
  • ***
  • Posts: 38
    • View Profile
Re: Family survivor 69 Camaro
« Reply #49 on: May 12, 2018, 12:06:20 PM »

gma_camaro

  • Member
  • ***
  • Posts: 38
    • View Profile
Re: Family survivor 69 Camaro
« Reply #50 on: May 12, 2018, 01:19:56 PM »
And some shots of the exhaust manifolds:








gma_camaro

  • Member
  • ***
  • Posts: 38
    • View Profile
Re: Family survivor 69 Camaro
« Reply #51 on: May 13, 2018, 12:02:53 PM »
Kurt, You had asked for pictures of the engine mount bolts. Let me know if this what you are looking for.

Driver side. This one is still installed



Passenger side. Could not get a good one of the rear view and had to pull bolt to get cable off from around the exhaust manifold.

gma_camaro

  • Member
  • ***
  • Posts: 38
    • View Profile
Re: Family survivor 69 Camaro
« Reply #52 on: May 28, 2018, 08:33:49 PM »
Got a few more parts off this week and am about ready to pull the front clip. Here are some more detail pictures, as usual there are more in the album if you want to see more. Send me a note for any follow up details. Lug nuts are in there too, they had a mix of markings and are pending sold to a guy on yenko.net.

First question - is this an original battery cable? The battery clamp is not original of course but the starter end terminal looks factory:



Master cylinder and prop valve:







Tag that was on the master cylinder cover bail - it fell off with a minor disturbance. Not sure how it was still on. Is this original?


Tag on carb:


Water pump:

gma_camaro

  • Member
  • ***
  • Posts: 38
    • View Profile
Re: Family survivor 69 Camaro
« Reply #53 on: May 28, 2018, 09:03:41 PM »
Congrats and.....wow.  Takes guts....

Can you take a photo of the dash panel top?  Like to see what the "suede paint" looks like after all these years.  thanks!

Finally remembered to snap these - sorry about the wait. Got them in a few different looks - from inside, outside through the windshield. Paint looks great just not sure the pictures do it justice. The car sat inside most of the time since the mid-80s in a garage with not a lot of windows so that saved it a lot of paint fade.




firstgenaddict

  • Hero Member
  • *****
  • Posts: 2882
  • caretaker of 1971 LT1's 11130 & 21783
    • View Profile
    • Groome Family Automobiles
Re: Family survivor 69 Camaro
« Reply #54 on: May 29, 2018, 08:49:08 PM »
WOW 
Mardsen Nut on the Motor mount... does anyone know is that original?

That dash pad will clean up nicely... here is an original black dash pad I cleaned



Seats will also clean nicely


James
Collectin' Camaro's since "Only Rednecks drove them"
Current caretaker of 1971 LT1's - 11130 and 21783 Check out the Black 69 RS/Z28 45k mile Survivor and the Lemans Blue 69 Z 10D frame off...
https://plus.google.com/photos/112392262205377424364/albums?banner=pwa

BULLITT65

  • Hero Member
  • *****
  • Posts: 4476
    • View Profile
Re: Family survivor 69 Camaro
« Reply #55 on: May 29, 2018, 09:14:43 PM »
James did you use anything special to clean it with?. I have use baby oil in the past, but I would think there is a better product. Also have you repaired any that were separating?
1969 garnet red Z/28 46k mile unrestored X77
-Looking for 3192477 (front) spiral shocks 3192851 (rear)
-Looking for an original LOF soft ray windshield
-Looking for original Delco side post negative battery cable part # 6297651AV

bcmiller

  • CRG Member
  • *****
  • Posts: 4010
    • View Profile
Re: Family survivor 69 Camaro
« Reply #56 on: May 30, 2018, 12:41:49 AM »
I have seen that type of nut used on engine mounts before - but can NOT say for sure if it was on a 69 Camaro.

For what it is worth, reproduction parts sold by this company use the same type.
https://www.camarocentral.com/1967_1971_Engine_Mount_Thru_Bolts_p/enc-17f.htm


Bryon / 1968 Camaro SS 396 coupe - now old school 468 big block
1967 Camaro RS/SS 396 coupe L35/M40 - 4 generation family project
Looking for 68 Camaro with body # NOR 181016

firstgenaddict

  • Hero Member
  • *****
  • Posts: 2882
  • caretaker of 1971 LT1's 11130 & 21783
    • View Profile
    • Groome Family Automobiles
Re: Family survivor 69 Camaro
« Reply #57 on: June 01, 2018, 04:06:22 PM »
A tooth brush and/or a fingernail brush and I believe denatured alcohol - which is used to clean rubber and vinyl rollers in the printing industry.

Yes I have reattached the covers to the backers... the backing has to be flattened using heat first.
James
Collectin' Camaro's since "Only Rednecks drove them"
Current caretaker of 1971 LT1's - 11130 and 21783 Check out the Black 69 RS/Z28 45k mile Survivor and the Lemans Blue 69 Z 10D frame off...
https://plus.google.com/photos/112392262205377424364/albums?banner=pwa

KurtS

  • CRG Coordinator
  • *****
  • Posts: 5884
    • View Profile
Re: Family survivor 69 Camaro
« Reply #58 on: July 18, 2018, 04:29:57 AM »
Yes, that's the original cable and RC is the broadcast code for the drum brake system.

What do you see as the height and width measurements of the T, P, and B stamps? I see about 7/8" high on the T and 3/4 on the P & B, but it's hard to be sure.

Thanks!
Kurt S
CRG

69z28rsbilly

  • Member
  • ***
  • Posts: 79
    • View Profile
Re: Family survivor 69 Camaro
« Reply #59 on: August 06, 2018, 03:27:11 PM »
James what adhesive did you use to reattach the dash pad cover to the hard plastic backer ? Any tips or tricks in doing this....thanks
X33 72 72 RS
X33 71 71 RS
X33 10 10