Author Topic: Removed Muncie  (Read 5809 times)

hihorse

  • Member
  • ***
  • Posts: 233
    • View Profile
Removed Muncie
« on: August 16, 2016, 07:37:49 PM »
removed the M20 from my 69  396/325HP 12B X66 car. Are the flywheel bolts (letter P in middle) original?

hihorse

  • Member
  • ***
  • Posts: 233
    • View Profile
Re: Removed Muncie
« Reply #1 on: August 16, 2016, 08:00:21 PM »
heres the bellhousing from the car

hihorse

  • Member
  • ***
  • Posts: 233
    • View Profile
Re: Removed Muncie
« Reply #2 on: August 19, 2016, 07:04:10 PM »
driveshaft

hihorse

  • Member
  • ***
  • Posts: 233
    • View Profile
Re: Removed Muncie
« Reply #3 on: August 19, 2016, 07:06:16 PM »
rough weld

bcmiller

  • CRG Member
  • *****
  • Posts: 4011
    • View Profile
Re: Removed Muncie
« Reply #4 on: August 19, 2016, 07:08:50 PM »
Do you see any hint of stripes on the driveshaft?

And can you do an accurate measurement of the driveshaft (measure from the center of one universal joint to the center of the other universal joint).  It usually is easiest to do that if you have help.

I can't help with the flywheel bolts.
« Last Edit: August 20, 2016, 01:09:21 AM by bcmiller »
Bryon / 1968 Camaro SS 396 coupe - now old school 468 big block
1967 Camaro RS/SS 396 coupe L35/M40 - 4 generation family project
Looking for 68 Camaro with body # NOR 181016

jdv69z

  • Hero Member
  • *****
  • Posts: 1275
  • 69 RS Z/28 52E
    • View Profile
Re: Removed Muncie
« Reply #5 on: August 20, 2016, 11:59:36 PM »
I don't know  on the flywheel bolts, but I'm guessing original, only because I don't know any hardware stores or anywhere else where one would buy bolts marked like that.
Jimmy V.

KurtS

  • CRG Coordinator
  • *****
  • Posts: 5884
    • View Profile
Re: Removed Muncie
« Reply #6 on: August 21, 2016, 11:50:33 PM »
That's a lot of balance weights. I don't recall seeing the washer style weight before....
Kurt S
CRG

cook_dw

  • Hero Member
  • *****
  • Posts: 3981
    • View Profile
Re: Removed Muncie
« Reply #7 on: August 22, 2016, 12:31:04 AM »
That does not look like a factory weld.  I would venture to say there was a repair and a rebalance in its life.

Like the rallye green and short spoiler.

ko-lek-tor

  • Hero Member
  • *****
  • Posts: 1858
  • someday I'll get one finished
    • View Profile
Re: Removed Muncie
« Reply #8 on: August 22, 2016, 02:10:02 AM »
That does not look like a factory weld.  I would venture to say there was a repair and a rebalance in its life.

Like the rallye green and short spoiler.
X2
Bentley to friends :1969 SS/RS 396 owned 79
1969 SS 350 (sold)
1969 D.H.COPO replica 4spd. owned since 85
1967 302 4 spd 5.13

X33RS

  • Hero Member
  • *****
  • Posts: 1092
    • View Profile
Re: Removed Muncie
« Reply #9 on: August 22, 2016, 02:50:54 AM »
The washer, I commonly see from the local driveshaft shop here when building or balancing shafts, tacked on exactly like that.

ko-lek-tor

  • Hero Member
  • *****
  • Posts: 1858
  • someday I'll get one finished
    • View Profile
Re: Removed Muncie
« Reply #10 on: August 22, 2016, 11:18:07 AM »
Upon further study of the picture of the whole shaft, I wonder if the previous owner or a shop was convinced that something was amiss since the yokes are/were clocked in an odd way as the other DSs discussed elsewhere on this site? For whatever reason, it is apparent that this driveshaft is not 'clocked' like the others now. Either it was clocked in its current configuration when repaired or it was one of those, it's not broke, but I gotta fix it scenarios?
Bentley to friends :1969 SS/RS 396 owned 79
1969 SS 350 (sold)
1969 D.H.COPO replica 4spd. owned since 85
1967 302 4 spd 5.13

hihorse

  • Member
  • ***
  • Posts: 233
    • View Profile
Re: Removed Muncie
« Reply #11 on: August 22, 2016, 03:21:58 PM »
Do you see any hint of stripes on the driveshaft?

And can you do an accurate measurement of the driveshaft (measure from the center of one universal joint to the center of the other universal joint).  It usually is easiest to do that if you have help.

I can't help with the flywheel bolts.

i didn't see any  hint of the stripes. Driveshaft measures 49.5"

hihorse

  • Member
  • ***
  • Posts: 233
    • View Profile
Re: Removed Muncie
« Reply #12 on: August 24, 2016, 05:15:04 PM »
is cover correct?