Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Terry69RSZ28

Pages: [1] 2 3 ... 5
1
Originality / Re: Positraction tag
« on: January 23, 2020, 03:15:55 PM »
Thanks for the photo, Jimmy!

2
Originality / Re: Positraction tag
« on: January 23, 2020, 03:49:14 AM »
Thanks, Byron!
Much appreciated, Terry

3
Originality / Positraction tag
« on: January 23, 2020, 01:19:47 AM »
Hi,
What colour is an original, assembly line correct positraction tag for a 1969 Z28? Is it red or orange?
Thanks, Terry

4
Originality / Re: CE Block crankshaft and piston
« on: December 16, 2019, 09:24:31 PM »
Thanks for the information, Steve! Always learn something new...
Regards, Terry

5
Originality / Re: CE Block crankshaft and piston
« on: December 16, 2019, 06:04:13 AM »
Hi Jim,
The photos you provided look identical to the two I posted. My CE is a late 69 date code block. Thanks for posting.  :)

6
Originality / Re: CE Block crankshaft and piston
« on: December 16, 2019, 03:37:11 AM »
Hi Everyone,
Without taking the engine apart, does the photo showing the top of the piston point towards an original piece? This block does have the correct 1178 crank. Thanks, Steve for the verification.

7
Decoding/Numbers / Re: Opinions on this DZ stamp
« on: December 16, 2019, 02:34:26 AM »
Hi William,
Thanks for your reply. Much appreciated!
Regards, Terry

8
Originality / CE Block crankshaft and piston
« on: December 16, 2019, 02:27:34 AM »
Hi,
Are these correct for 1969 Z28 CE warranty block? It is standard bore, the pistons have no numbers and the crankshaft has one notch.
Thanks, Terry

9
Decoding/Numbers / Opinions on this DZ stamp
« on: December 15, 2019, 03:57:30 PM »
Hi,
Is this stamp original? The block casting is 3932386 with a date code of September 5, 1968. VIN is on engine pad but is concealed by the seller. Thanks for your expertise.
Terry

10
Decoding/Numbers / Re: CE Block
« on: October 22, 2019, 02:07:11 PM »
Much appreciated, Kurt!

11
Decoding/Numbers / Re: CE Block
« on: October 18, 2019, 05:43:38 PM »
Bentley,
Thanks for the clarification regarding the serial number.
Very much appreciated, Terry :)

12
Decoding/Numbers / Re: CE Block
« on: October 17, 2019, 06:02:28 PM »
Thanks for all the comments regarding this CE block. I am hoping Kurt or anyone else knowledgeable on warranty blocks could provide some further insight on the stamp and why the number starts with a zero.
Regards, Terry :)

13
Decoding/Numbers / Re: CE Block
« on: October 15, 2019, 03:18:19 AM »
Since the serial number is 06579, was this CE block produced at the Flint Motor Plant (L6 engines)?

14
Decoding/Numbers / Re: CE Block
« on: October 14, 2019, 10:07:27 PM »
Yes, it has the 1/4 inch square NPT plug.

15
Decoding/Numbers / Re: CE Block
« on: October 14, 2019, 05:15:15 PM »
Hi Jim,
Thanks for your input regarding this CE short block. It is listed at $3025 US.
Is this a high, average or low price for a CE block?
Thanks again.

Pages: [1] 2 3 ... 5
anything