Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - camaroman1969

Pages: [1] 2 3 ... 10
General Discussion / Broadcast sheet/Build Sheet Type setting process
« on: November 04, 2018, 11:46:52 PM »
Hey Guys...Does anyone here, know of anyone who works with filling out and types in info to a Build sheet/Broadcast sheet???  I have a Broadcast sheet that is blank, but need someone to enter info on sheet with correct type set and correct size.  Please give me a shout if anyone here can lead me to that person.  Thanks for your time.  Don

General Discussion / Bellhousing alignment procedure
« on: June 19, 2018, 01:44:51 AM »
Hello everyone....Question:  Does anyone here know the proper procedure on aligning a bellhousing???  We used a dial indicator, but everytime we would recheck the reading, they would "differ" from previous reading.  Used new dowel pins also.  Still no good.  Going to purchase some stock dowel pins and see if that helps.  Any assistance would be appreciated guys.  Thanks!

General Discussion / Harrison Radiator
« on: February 28, 2018, 03:37:05 AM »
Hi Guys!  Does anyone have knowledge on a Harrison Radiator, why these are constructed with a "curved neck" top radiator out-let??  This was on all the 4-core
radiators that were equipped with a 396 or 427 big block engine.  This curved neck is available in some of the Camaro parts book, that you can insall on a Harrison non-curved tank. 

General Discussion / Re: Steering Wheel Shroud
« on: February 24, 2018, 04:41:29 AM »
Thank you very much Mike and Bill for the "vacuum chrome" info.  I'm going to contact them both.    Don

General Discussion / Steering Wheel Shroud
« on: February 23, 2018, 04:13:23 AM »
Does anyone know if the steering wheel shrouds on 69 Camaros, had the edge of the shroud "painted" or was it "vacuum plating"???  The part# was 3939760. 
Some of the other dash cluster parts have this "chrome like" finish, on the outside edges of that part.  OK guys, give me a shout if you have any knowledge of someone who does this kind of restoration.   Thanks!!    Don

General Discussion / 1969 Camaro Headrests
« on: January 11, 2018, 03:22:08 PM »
Looking for some info on headrests for a 1969 Camaro.  A guy on e-bay told me there is a company in California that restore these.  Anyone know about this company or of another restoration place that restores these???  If you do by chance, please leave word here and I'll check back.  Thanks guys..

General Discussion / Vacuum shortage
« on: December 26, 2017, 12:24:40 AM »
Hi Guys...I have a BB 396/375 that has a "vacuum" issue.  Currently pulling about 9.0 inches.  I believe i should be creating around 11 - 12 inches.  It has a slightly  hotter cam than stock for this engine.  Before we dive into it, I just thought I'd ask the question of what might be the "root cause".  The cam maybe  a little.  We suspect may the intake manifold.  Could be slightly warped?not square???  What it does when it gets hot, idles down and stalls out.  Cold, it runs OK.  Anyhow, any input would be helpful before we go nuts.  Thanks guys!!

General Discussion / Re: Defogger switch
« on: December 20, 2017, 11:58:30 PM »
Thanks guys for all your input.  This will help. 

General Discussion / Re: Defogger switch
« on: December 05, 2017, 04:25:46 AM »
Thanks Bill.  Doesn't look like its gonna be a easy task to install this defogger.

General Discussion / Defogger switch
« on: December 05, 2017, 02:03:24 AM »
I would like to install a "defogger blower" on my 1969 Camaro SS/RS.  Question: Does one have to cut dash, or is this already pre-cut behind the wood grain covering??  All comments will be appreciated.  Thanks guys!   Don

General Discussion / Re: Slick size?
« on: August 16, 2017, 09:22:24 AM »
Would the original rally wheels (15 x 7 )  work??  I'm trying to determine what size tire would fit on these rims.  I really don't want to run the biggest tire I can.
Thanks for the input.  Anybody else, please chime in. 

General Discussion / Re: Slick size?
« on: August 14, 2017, 01:12:43 PM »
This size would fit using stock 15 x 7 rim without rubbing????  Thanks

General Discussion / Slick size?
« on: August 11, 2017, 01:15:56 AM »
Does anyone know, what size slicks fit under a stock 1969 Camaro SS body??  I will be mounting them on 15 x 7 rally wheels.  Thanks!

General Discussion / Re: 1969 Camaro Over Heating issue
« on: July 18, 2017, 12:04:08 PM »
Hi!  Thanks for your time on commenting on my issue.  We replaced thermostat with a 180 F one.  It's a "high flow one".  I have a 1969 Camaro SS/RS 397/375
car.  Comp. ratio is 11.0 to 1.  Pretty much all factory set-up.  No serp. belts being used here....factory originals only.  It could be a bad sending unit.  I think I'll change it out just so I know what I have here.  Actually, yesterday, we installed a new "pusher fan" in front of radiator, for added insurance when car is driven.  I have a 4 core, 4 row radiator in it now.  Well, this is where I'm at Ban617.  Any other ideas will be welcome.  Thanks for chiming in.    Don

General Discussion / Re: 1969 Camaro Over Heating issue
« on: July 11, 2017, 02:12:59 AM »
bcmiller.....My Camaro ran good last season...mid-way in the gauge.  Car ran good.  Now when it approaches the 3/4 point into the gauge, car goes crazy.  Won't idle right, shifts hard, etc.  This block is really touchy.  Major headache.......

Pages: [1] 2 3 ... 10