Author Topic: Wiper arms  (Read 3018 times)

67conv6cyl

  • Member
  • ***
  • Posts: 496
    • View Profile
Wiper arms
« on: September 24, 2022, 10:31:03 PM »
Dose anyone know the correct part numbers for convertible wiper arms.
I have a parts book however no part numbers on this item.

I just want to see if my 67 wiper arms are the correct originals.

67conv6cyl

  • Member
  • ***
  • Posts: 496
    • View Profile
Re: Wiper arms
« Reply #1 on: September 24, 2022, 10:40:59 PM »
Here is a. Picture of my wiper arm

Petes L48

  • Hero Member
  • *****
  • Posts: 790
    • View Profile
Re: Wiper arms
« Reply #2 on: September 25, 2022, 01:42:51 AM »
It's UPC 1 Sheet A3 in the AIM.

3916687, or 3916688 is the optional for a vert.  I assume the Trico was primary and Anco was the optional

FWIW I also saw 3893839 Trico listed in a 1966 parts book.

rare396bronze

  • Member
  • ***
  • Posts: 281
    • View Profile
Re: Wiper arms
« Reply #3 on: September 25, 2022, 02:44:20 AM »
1969 Chevrolet parts book says 3916688  trico 67-68 camaro convertible! Hope this helps. They are shorter than the coupe!

67conv6cyl

  • Member
  • ***
  • Posts: 496
    • View Profile
Re: Wiper arms
« Reply #4 on: September 25, 2022, 07:16:45 PM »
So the wiper arm I posted is not correct for a 67 convertible?

rare396bronze

  • Member
  • ***
  • Posts: 281
    • View Profile
Re: Wiper arms
« Reply #5 on: September 25, 2022, 07:27:25 PM »
I would take measurement of the arm and post it in a picture off it. I don't think the the gm part is stamped on the arm!

Petes L48

  • Hero Member
  • *****
  • Posts: 790
    • View Profile
Re: Wiper arms
« Reply #6 on: September 25, 2022, 07:51:42 PM »
Your picture showed Patent numbers, not part numbers.  I don't recall the part number being stamped or cast on the arms either.

67conv6cyl

  • Member
  • ***
  • Posts: 496
    • View Profile
Re: Wiper arms
« Reply #7 on: September 26, 2022, 02:07:01 AM »
Hear is picture of the complete arm

rare396bronze

  • Member
  • ***
  • Posts: 281
    • View Profile
Re: Wiper arms
« Reply #8 on: September 26, 2022, 03:14:18 AM »
Looks right just checked my convertible. With my blade off 13 1/4 long fully pushed down. All the numbers on the arm matches mine.

169INDY

  • Hero Member
  • *****
  • Posts: 1786
    • View Profile
Re: Wiper arms
« Reply #9 on: September 26, 2022, 03:23:18 AM »
Are all of the Short Arms stamped "CONV" ??
My 69's are.

Jim
Jim
68 SS/RS L35 Th-400 LOS
69 Pace Car L48 Th-350 LOS
68 Z28 M21 LOS

dannystarr

  • Hero Member
  • *****
  • Posts: 1745
    • View Profile
Re: Wiper arms
« Reply #10 on: September 27, 2022, 04:17:35 AM »
I know the convertible arm is 1" shorter than hard top. At least in '67 & '68. Danny

Sauron327

  • Hero Member
  • *****
  • Posts: 1359
    • View Profile
Re: Wiper arms
« Reply #11 on: September 27, 2022, 02:38:20 PM »
I know the convertible arm is 1" shorter than hard top. At least in '67 & '68. Danny
69 too. Restored all three years and sold off all my convertible wiper arm stock. Ready to scrap my hardtop ones. Tired of saving inventory.

rare396bronze

  • Member
  • ***
  • Posts: 281
    • View Profile
Re: Wiper arms
« Reply #12 on: September 27, 2022, 02:49:40 PM »
Don't see conv stamped on my 68 arms or a spare set i have. Only thing stamped on them is what is pictured on 67conv6cyl!

Pacecar

  • Member
  • ***
  • Posts: 205
    • View Profile
Re: Wiper arms
« Reply #13 on: September 27, 2022, 02:56:31 PM »
67 Arms should be brighter than 68 and 69, noticeable at the knuckle

Petes L48

  • Hero Member
  • *****
  • Posts: 790
    • View Profile
Re: Wiper arms
« Reply #14 on: September 27, 2022, 06:27:11 PM »
Didn't see a CONV on my 67 arms either, but was using a flashlight and small mirror, while staying away from the paint.