Author Topic: Hurst Shifter Adjusting Blocks/Rods  (Read 10242 times)

jdv69z

  • Hero Member
  • *****
  • Posts: 1275
  • 69 RS Z/28 52E
    • View Profile
Hurst Shifter Adjusting Blocks/Rods
« on: September 30, 2014, 06:40:21 PM »
I'm trying to free up the adjusting blocks that thread onto the shift rods on an after market competition plus. They are frozen and will not more. I've tried soaking in WD 40 for 24 hours, and even heating the blocks themselves to try to free them up, but nothing haven't had any success. Anything else I can soak the in or any other ideas?
Jimmy V.

maroman

  • Hero Member
  • *****
  • Posts: 1067
    • View Profile
Re: Hurst Shifter Adjusting Blocks/Rods
« Reply #1 on: September 30, 2014, 06:52:49 PM »
More heat an patience.
Doug  '67 RS/SS 396 auto I know the car since new

Stingr69

  • Hero Member
  • *****
  • Posts: 901
    • View Profile
Re: Hurst Shifter Adjusting Blocks/Rods
« Reply #2 on: September 30, 2014, 07:35:31 PM »
Use an Oxy-Acetylene smoke wrench to the adjusting block.  Get it to dull red color then spray with PB Blaster.  Makes a lot of smoke and smell so do it outdoors.  That is how I get the threaded engine block plugs out.  It should work for the shift rods too.  WD-40 does not work as well for this in my experience.  The PB Blaster is best here.

-Mark.

x77-69z28

  • Hero Member
  • *****
  • Posts: 1058
    • View Profile
Re: Hurst Shifter Adjusting Blocks/Rods
« Reply #3 on: October 01, 2014, 01:53:23 AM »
I second PB blaster. Much better than wd-40
69 Z/28 X77 burnished brown, 711 int 05A bought in 78
70 Z28 forrest green, green int, M40, bk vinyl roof PROJECT
99 SS hugger orange 6spd NO TTOPS bought new 1 of 54
15 z/28 Arctic white, A/C 505 HP #251

jdv69z

  • Hero Member
  • *****
  • Posts: 1275
  • 69 RS Z/28 52E
    • View Profile
Re: Hurst Shifter Adjusting Blocks/Rods
« Reply #4 on: October 01, 2014, 02:59:03 PM »
Thanks, got the rods soaking now in PB Blaster. I'll give it 24 hours, and then try the heat again if necessary. Odd thing is, the parts really aren't very rusty at all. But I guess it doesn't take much for those fine threads to get frozen.
Jimmy V.

Sauron327

  • Hero Member
  • *****
  • Posts: 1359
    • View Profile
Re: Hurst Shifter Adjusting Blocks/Rods
« Reply #5 on: October 01, 2014, 03:24:15 PM »
I grab my torch right away for anything that is stubborn enough to require long term penetrant soaking. Why wait days when a job can be done in minutes?

Kelley W King

  • Hero Member
  • *****
  • Posts: 1410
    • View Profile
Re: Hurst Shifter Adjusting Blocks/Rods
« Reply #6 on: October 01, 2014, 03:27:53 PM »
I have been impressed with evaporust. When trying to remove headlight adjusters from the plastic parts I tried everything. Finally sprayed them with evaporust and the next night they turned right out. Since then I have sprayed rusted threads of bolts and they turn right out.
69 Z28 RS Scuncio Hi Performance
69 SS L78
67 SS Chevelle
64 Corvette
66 GTO Tiger Gold
77 Trans Am Special Edition

ko-lek-tor

  • Hero Member
  • *****
  • Posts: 1858
  • someday I'll get one finished
    • View Profile
Re: Hurst Shifter Adjusting Blocks/Rods
« Reply #7 on: October 01, 2014, 04:04:12 PM »
Love my "fire wrench" (torch), but soaking in vinegar (gallon jug), does wonders and is cheap. I have posted before that supposedly best penetrating oil is a 50/50 mix of acetone and trans fluid.
Bentley to friends :1969 SS/RS 396 owned 79
1969 SS 350 (sold)
1969 D.H.COPO replica 4spd. owned since 85
1967 302 4 spd 5.13

jdv69z

  • Hero Member
  • *****
  • Posts: 1275
  • 69 RS Z/28 52E
    • View Profile
Re: Hurst Shifter Adjusting Blocks/Rods
« Reply #8 on: October 01, 2014, 08:32:58 PM »
So I don't have a torch per se, only a little propane gas bottle torch. So how hot do I get the parts?
Jimmy V.

maroman

  • Hero Member
  • *****
  • Posts: 1067
    • View Profile
Re: Hurst Shifter Adjusting Blocks/Rods
« Reply #9 on: October 01, 2014, 09:27:28 PM »
Wiki claims about 2000 degrees.
Doug  '67 RS/SS 396 auto I know the car since new

ko-lek-tor

  • Hero Member
  • *****
  • Posts: 1858
  • someday I'll get one finished
    • View Profile
Re: Hurst Shifter Adjusting Blocks/Rods
« Reply #10 on: October 01, 2014, 10:35:41 PM »
So I don't have a torch per se, only a little propane gas bottle torch. So how hot do I get the parts?
If you can put a wrench on the bolt (use glove) apply pressure with one hand while heating with other until it turns. This is one way. The other is get 'er cherry red and let it cool. I hope you are taking the shifter off the car to heat it. With out experience in heating parts, you risk catching the car on fire if part left on the car. Make sure you have a fire extinguisher near by and nothing flamable in the area. Garage near me scrapped cars for cash and some kid working there was draining gas tank by drilling bottom of tank with an electric drill. Burnt the place down.
Bentley to friends :1969 SS/RS 396 owned 79
1969 SS 350 (sold)
1969 D.H.COPO replica 4spd. owned since 85
1967 302 4 spd 5.13

JoeC

  • Hero Member
  • *****
  • Posts: 502
    • View Profile
Re: Hurst Shifter Adjusting Blocks/Rods
« Reply #11 on: October 02, 2014, 12:52:06 PM »
had this problem many times

be careful as too much force with snap off the end of the rod

if it looks like the threaded end won't move, I hack saw a slice in it on the thin part parallel to the rod, not deep enough to hit the thread

it ruins the rod end but saves the rod


jdv69z

  • Hero Member
  • *****
  • Posts: 1275
  • 69 RS Z/28 52E
    • View Profile
Re: Hurst Shifter Adjusting Blocks/Rods
« Reply #12 on: October 06, 2014, 07:32:09 PM »
Success! Heat worked. Now coated with anti seize to prevent relapse.
Jimmy V.