Messages

1

Originality / what are stripe measurements for a Feb. 69 LOS built car

« on: March 05, 2013, 05:48:00 AM »

does anyone have the measurements for the trunk stripes? I just want to make sure the stripes are in the correct location.this is on a 69 Z/28 built feb in LOS.
                            Thanks Rich

2

Restoration / were door jamb switchs painted?????

« on: February 07, 2013, 06:24:52 AM »

My 69 Z is just about ready for paint.did the door jamb switchs get painted or were they installed after the body was painted?
                 Rich

3

General Discussion / where can I send my water pump to get rebuilt

« on: December 01, 2012, 11:06:55 PM »

I have my orgial pump that I want to get redone. who good at this kind of work?

4

General Discussion / Re: where can I find MADE IN USA rear wheel cylinders

« on: November 27, 2012, 06:00:58 AM »

these are for a 69. I dont have the orginals

5

General Discussion / Re: 12 bolt backing plates

« on: November 27, 2012, 05:12:00 AM »

Found this on-topic thread in a search..

Also regarding the backing plates..
I aquired a used pair that have splash shields welded to them. I didn't know splash shields were ever added to drum backing plates and thought someone must have once added them. I was also considering removing them until I did a short Google search and found some with..

The afore mention In-Line Tube website has the option of with and without..
http://inlinetube.com/Drum%20Brakes/Drum%20Brakes.htm



Question: Where the shielded plates ever a Camaro option, standard or never available on them? If not, what were these normally fitted to?

Also, looking at the ones that I have that came off a 68 Camaro (no idea if original to the car), were the welds normally that rough? This is mainly why I assumed a back-yard welder had added them.




those were added.

6

General Discussion / where can I find MADE IN USA rear wheel cylinders

« on: November 27, 2012, 05:09:34 AM »

all I can find is made in china is there such a thing anymore?

7

Originality / Re: what gloss level should I paint the following parts on a 69 z28

« on: November 25, 2012, 07:14:58 PM »

cowl air cleaner
heater box
engine brackets
engine pulleys
wiper motor
bumper brackets
                     thanks Rich

 guess I'll shot the air cleaner,heater box and wiper motor gloss and everything else with less gloss
                 thanks again

8

Originality / Re: what gloss level should I paint the following parts on a 69 z28

« on: November 24, 2012, 09:41:44 PM »

alt bracket,p/s bracket

9

Originality / what gloss level should I paint the following parts on a 69 z28

« on: November 24, 2012, 08:57:43 PM »

cowl air cleaner
heater box
engine brackets
engine pulleys
wiper motor
bumper brackets
                     thanks Rich

10

Restoration / splash shields. who sells the quality ones?

« on: November 14, 2012, 05:40:27 AM »

i see the re pop brand.  are there any other brands out there. they seemed abit thin.

11

Originality / Re: Source for 'EY' Coil Springs for '69 Z28/RS??

« on: November 12, 2012, 10:32:58 PM »

this is Jim @ HBC 69

12

Originality / Re: Source for 'EY' Coil Springs for '69 Z28/RS??

« on: November 12, 2012, 10:30:54 PM »

heres an orgianal

13

Originality / Re: Source for 'EY' Coil Springs for '69 Z28/RS??

« on: November 12, 2012, 06:37:31 AM »

Moog 6320. here is Garys car with the 6320 spring

14

General Discussion / Re: did cowl hooded cars have under hood lights

« on: November 10, 2012, 12:14:34 AM »

I saw the aim,but Ive never seen one on a car

15

General Discussion / did cowl hooded cars have under hood lights

« on: November 09, 2012, 11:38:56 PM »

my orginal flat hood came with a light.what about cowl hoods?