Topics

What fluid would you guys recommend to use in my Muncie M21 Transmission ? I've had the trans rebuilt (twice) and after both rebuilds I am having the same shifting issues ( upshifting from 2nd to 3rd ). I'm thinking I might have the wrong fluid in it which is casing the hard shifting problems.

I'm just being curious but I wanted to know what a 1969 Z28 Camaro CV fan clutch sells for ?

When did they start using bolts ( instead of using nuts ) to attach shifter rod levers on a 1969 Muncie transmission ? The transmission is a 660 main case and has a 306 side cover.

Does anyone know what the correct part number  for a late September Camaro drivers side door mirror?

I'm restoring some YH rims and have a concern about the area where the sides of the tire meet the edge's of the steel rim. The area is pitted and I'm not sure if this will seal properly. If rims are pitted can't tire shops use a sealer for just this situation ?

I recently took out my shifter rods and noticed  my levers were stamped 5615 on both rods. I looked up those numbers and they were installed on 1970-72 Camaro Z28,s .My Z28 is a early September built car. Would it be possible that the 5615 rods and levers were used on my car since it was such a late built car ?

I am looking to replace the trim rings on my 1969 Camaro Z28.  Don't really need originals (I'm just too hard on them) Who sells good reproduction rings?

I'm restoring some YH rally rims for my Camaro this winter, after sandblasting I noticed a couple of the rims are pitted from rust . What's the best way to go about repairing those areas that are pitted ?

I have a M21 Muncie Transmission that has the vin. no. 19N642693 and is stamped P9D25B. Would like to find the car it came from.

I want to pick up the paint for my ralley rims that I'm going to paint. I'm not sure about the finishes, should the back be a semi gloss Black and the front a semi-gloss Argent Silver ?

I noticed that my coil wire terminal is bad on my 69 Z28. Where can I find an original wire terminal. It's in the shape of the letter F and has two wires connected to it.

After years of not having a working windshield washer pump (my piston seal was worn out) I finally got it working again ! iI wanted to rebuild my original pump and there is no one that sells a complete rebuild kit for this pump, the only rebuildalbe part that is sold is the tri-port o-ring seal. I ended up buying an Anco pump from RockAuto ($30.88), took apart the pump, removed the new piston and used it in my original pump. My pump works like brand new !

My 1969 camaro has seat belts most dated 19 A, one 18 A and one dated 28 A. I have an 9 A built car, I know the seat belts are dated early for my car and I don't think they were changed but do you guys think that the car could of be assembled at the factory with these belts?

I'm looking at a 837 alt thats dated H 25 9. My car was built 9 A 9 and the motor is stamped H 25. Would this alternator be too late for my car?

What would cause my 69 Camaro to backfire? First time it happened when I was starting the car and today it happened when I was accelerating on the highway.

My seat belts in my camaro read 18-A-69, how do I decode them?

Does anyone sell rebuild kits for a 1969 Camaro Delco- Moraine rear wheel cylinder ?

After many years I've finally decided to fix my windshield washer pump, where would I find new seals? I'm pretty sure the piston o-ring is wore out.

Need a new fan belt for my 1969 Z28, the last one came from Rick's Camaro and did not last. Can you guys recommend where I could find one.

Does anyone have a picture of an original rear tailpipe hanger?

I'm looking at some used original wittek smog pump clamps, how could I determine what is a fair price to offer the seller for the clamps.

I'm in need of a drivers side tailpipe hanger, does anyone know where I could find one ?

Did GM stamp "YH" axle shafts with the letters "YH"?

I'm looking at a B.U. rear end  with a casting date of I-7-9 and a a axle tube stamp of 0916 G2 E. Would this date work with my 1969 Z28. My date on my trim tag is 09A.

I have a 1969 Z28 with the 302 motor, my plug on my oil pressuse switch is wore out, it is the original plug and I wanted to ask the crg members where I should look for a plug. I want to replace it with an original part.