News:

Classified ads are not allowed on the forum.

Main Menu
Menu

Show posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Show posts Menu

Messages - jonboy1216

#31
if you turn slowly in it will stay running. there is no set # of turns on the idle screws to start or end with that is for people who dont know how to tune a carb
#32
idle mixture screws can only be set correctly with a tach or vacuum gauge. with gauge or tach hooked up turn idle screw all the way in .then turn out slowly til the gauge or tach reads the highest number then stop and go to the other idle screw and repeat. and remember that one side can have a different setting. as in drivers side can be 1 turn out and pass side can be 3 turns out because each screw controls one idle circuit.hope this helps
#33
General Discussion / Re: Steering wheel wrap
May 31, 2010, 09:44:06 AM
can you post a pic after it is installed ?it might be a creative solution til my money tree is off life support steering wheel restos are costly
#34
Originality / Re: 68 remote mirror
May 25, 2010, 08:02:07 PM
mikefam    does the front of your 68 remote mirror base squared or come to a point like a 69? mine is squared and all the repos are pointed at the front
#35
thanks my 68l35rsss is do for a paint job and would like to purchase nos stuff but it may take a few years as my money tree is on life support :(
#36
Originality / 1968 side marker lights and bezels
May 20, 2010, 02:11:12 PM
what are the parts #s for the bezels and the lights?
#37
General Discussion / Re: Yenko ZL1 427
April 28, 2010, 07:59:10 PM
are you sure about the car ?im curious because i thought fred gibb had the 69 zl1s built and then chevrolet sent the ones he didnt keep to other dealerships.that being said yours would have the alt. setup that the other 68 had to be correct.
#38
General Discussion / Re: After market fit
April 19, 2010, 10:18:45 PM
try al knoch interiors his stuff is just like factory.didnt know pui give so much trouble
#39
General Discussion / Re: After market fit
April 19, 2010, 03:51:05 PM
what kind did you buy?
#40
Originality / Re: 68 MO 302 water pump?
April 17, 2010, 10:30:40 PM
thanks guys i will get the 1/2 326 pump for my car
#41
Originality / 68 MO 302 water pump?
April 16, 2010, 06:00:34 PM
an april 16 built MO 302 waht water pump should be on the thing?  i have been told that a 3859326 is correct .but i was on lucas restorations web site and they had pics of a june  68 rs z28 tore done from top to bottom and the pump that was on that car was 3839175 .any ideas what the difference is?
#42
Restoration / Re: restamped distributor
April 14, 2010, 10:09:58 AM
whos going to look at the engine that far back anyway.just clock your dist. to make it that much harder to read
#43
General Discussion / wiper refills
April 10, 2010, 08:20:50 PM
who makes correct wiper refills for a nos trico blades?
#44
General Discussion / Re: my new 1968 Z/28
April 10, 2010, 08:17:17 PM
should look good again all fixed up :)love the color combo
#45
Originality / Re: engine vin stamping?
April 07, 2010, 01:02:10 PM
thanks just got confused with the block having a different number