Topics

I just wanted to share this with everyone and CRG, I just dismounted 2 tires off my 67Z and one wheel is a service replacement wheel with DF code K19 5. here is some pics.
The part number sticker

The DF code and date

and the smaller size slot 1.00 inches

anyone know what number distributor cap the 302 engine used? was it the same as the 69z? 308R?

where did the seat belt clips go on the console to hold the belts? Did the deluxe belts get this clip?

what number should the fuel pump be for a 67Z? 40524 or 40725?

the screws that hold the back plate over the lenses are ther phillips or hex head screws? when these screws are removed you can take the cover off to access the lenses.

is this an original brake drum?

does anyone have a pic of the rubber stop that goes in the bracket? mine has broken off (SEE PIC)It goes inside the bracket and is held with the screw but mine is broken off

was the rear end houseing on a 67 camaro painted or not? Some say yes black,some say no. What will be acceptable on a march built 67 with a 12 bolt? Also the radius rod was that painted? 

was the oil pressure line clear plastic or black? I found out that a grommet is on the firewall and not a fitting,so I need to replace the line and add the grommet.

What was the part number for the 67 302 fuel pump? I cant find it anywhere in the books I have.

looking at the firewall to the left of the steering colum is an electrical plug with 2 connectors at differnt angles,the wires insde the car are heavy green wires.anyone know what this is for? here is a pic of it look next to the steering colum to the left.

Does anyone know where I can get my muncie shifter reconditioned? ???thanks ron.

Did the cowl plenum air cleaner get the 302 decal if the car came from the factory with that option? Im undecided on weather to put one on mine.

Jerry, Thanks a lot for the nice job you did on my 67 intake, it really makes the engine look good. Cant wait to get it in the car!

I know this is a topic discussed here before but I cant find the thred, here is a pic of my subframe and some say early 67 frames didint have the big holes and some only had 1 hole.My frame has holes in both sides but on top only 2 little holes instead of three,is this correct?

I know we have talked about this before with different opinions, I have a waterpump with a number on the front 3858326, is this the correct pump for a 03b z/28? I want to make sure before I send it out to get rebuilt.thanks Ron.

what color should the bumper brackets for the front and rear be on a 67 camaro? On a 67 you can see the corner brackets where the bumper wraps around the front corners and the rear brackets on the sides of the quarterpanels.Im thinking maybe black? but im not sure if they should be the color of the car.

What year was the first year for the blackout rear tailpan? Im thinking 68, but could be 69?

does anyone know if the black on the firewall was painted before the color of the car or after? Im just wondering about the overspray at the top of the firewall, Im guessing the black was painted first then the color of the car was oversprayed at the top cowl area and down the front about 2 inches. Jerrys book says they didnt mask this area so a overspray is correct and not a masked line seperation. Any pics ?

did they start hiding the vin under the heater core box in 67? I have a partial vin on my firewall there.

Im asking if anyone knows where exactly the oil pressure line goes thru the firewall? I think the hole my car has is right but just want to make sure,they pushed it thru the speed cable washer and there is a hole with nothing going thru and I think that might be the correct hole.look at pic

Just wanted to say happy thanksgiving to all my camaro friends out here and to Rich Fields and others who run this great website for us!! 

Im at the point where the engine for my 67Z is getting ready for paint and im wondering if the aluminum intake gets a little overspray of orange on the front? anyone know if the Hi Perf cars with the aluminum intakes get overspray?

does anyone know if a rear mounted antenna will interfere with a rear spoiler on a 67? also is there a template for drilling a rear mount antenna hole? my 67 has the rear antenna option but I never could bring myself to drilling a hole in a new GM quarterpanel.So now I would like to install the antenna only if it doesnt interfere with the spoiler.

is this vin number in the database? 124378N450500 lmk please thanks Ron.