Text only | Text with Images

CRG Discussion Forum

Camaro Research Group Discussion => General Discussion => Topic started by: 68Zproject on May 18, 2009, 03:56:28 PM

Title: D 80 in AIM?
Post by: 68Zproject on May 18, 2009, 03:56:28 PM
I haven't been on here in a while.  Did I miss something, as I have searched for hours, about the d-80 not being in the AIM (68 or 69)?
Title: Re: D 80 in AIM?
Post by: CVKUEBER on May 18, 2009, 04:27:49 PM
Not in my 68 AIM either. Will have to check my 69 AIM tomorrow.
Title: Re: D 80 in AIM?
Post by: Mark on May 18, 2009, 04:34:47 PM
Its in the 69 AIM, front spoiler only.  Its under Z28 for the rear mostly for paint striping.  Fisher installed the rear spoiler, GM the front.
Title: Re: D 80 in AIM?
Post by: rat pack on May 18, 2009, 05:49:37 PM
You have to look in the 67 AIM for 68 front spoiler mounting as for some reason that page is missing in the reprint of the 68 AIM.............RatPack................
Title: Re: D 80 in AIM?
Post by: 68Zproject on May 19, 2009, 10:48:47 AM
Well, I was kind of looking for a part number or  whatever reference told how to tell if the rear spoiler was GM or repro.  I remember reading it somewhere, but I've searched here quite a while and can't find anything other than the talk of the Camaro emblem being moved up when the factory intalled the spoiler.  I know mine was not factory installed, but am trying to determine if it's even GM and dealer installed.
Title: Re: D 80 in AIM?
Post by: CVKUEBER on May 19, 2009, 12:03:44 PM
Should have the casting number of 3916633 if it's a GM spoiler.
Title: Re: D 80 in AIM?
Post by: 68Zproject on May 19, 2009, 05:09:56 PM
Quote from: CVKUEBER on May 19, 2009, 12:03:44 PM
Should have the casting number of 3916633 if it's a GM spoiler.

Where?  It's on the car.  Do I need to take it off to find out?  Thanks.
Title: Re: D 80 in AIM?
Post by: KurtS on May 19, 2009, 09:14:43 PM
Yes, the # is on the bottom side.
Title: Re: D 80 in AIM?
Post by: 68Zproject on May 20, 2009, 01:51:38 AM
OK, thanks.
Title: Re: D 80 in AIM?
Post by: 68Zproject on May 30, 2009, 01:14:01 PM
3916633 on the bottom.  More parts I can sell.  P.S.  Anyway to tell if the trunk lid is GM?
Title: Re: D 80 in AIM?
Post by: rat pack on May 30, 2009, 08:40:53 PM
Yep, there is a run stamp in the center at the bottom as the repros do not have them......RatPack........
Title: Re: D 80 in AIM?
Post by: 68Zproject on May 31, 2009, 12:11:06 PM
On the raised metal below the jack instructions?  There's what looks like a 3 digit stamp D 8 ?, but I'm guessing as it's painted pretty thick.
Title: Re: D 80 in AIM?
Post by: JohnZ on May 31, 2009, 02:58:01 PM
Quote from: 68Zproject on May 31, 2009, 12:11:06 PM
On the raised metal below the jack instructions?  There's what looks like a 3 digit stamp D 8 ?, but I'm guessing as it's painted pretty thick.

Yup - Fisher Body run numbers are typically three characters - a letter for the stamping plant, and two numbers for the week of the year.
Title: Re: D 80 in AIM?
Post by: 68Zproject on May 31, 2009, 05:39:17 PM
Argghhh.  I've got a few holes to fix then.  I was hoping it was repro and I'd just get a used trunk lid.  Oh, well.  Thanks gentlemen.
Title: Re: D 80 in AIM?
Post by: Mark Powers on June 10, 2009, 08:34:09 AM
When did the d80 start being on cowl tag
Title: Re: D 80 in AIM?
Post by: bertfam on June 10, 2009, 09:06:47 AM
QuoteWhen did the d80 start being on cowl tag

Around May, 1969, but it wasn't always used.

Ed
Title: Re: D 80 in AIM?
Post by: Mark Powers on June 10, 2009, 06:58:46 PM
Thanks
Text only | Text with Images