CRG Discussion Forum
Welcome, Guest. Please login or register.
Did you miss your activation email?
April 17, 2014, 08:00:00 AM

Login with username, password and session length
Search:     Advanced search
Welcome to the CRG Discussion Forum!
Forum registration problems: Make sure you enter your email correctly and you check your spam box first. *Then* email KurtS2@gmail for help.
97120 Posts in 11686 Topics by 4578 Members
Latest Member: ronhill
* Home Help Search Login Register
+  CRG Discussion Forum
|-+  Camaro Research Group Discussion
| |-+  Maintenance
| | |-+  Rear Body Harness Replacement Procedure on a 69 Coupe
« previous next »
Pages: [1] Print
Author Topic: Rear Body Harness Replacement Procedure on a 69 Coupe  (Read 948 times)
Mac B
Member
***
Posts: 60


View Profile Email
« on: July 15, 2012, 01:32:35 PM »

I have determined that I need to replace my rear body harness.  This harness is routed between the dash and the trunk with a plug on the driver's side of the trunk for the tail light/turn signal/marker light harness.  What is the best way to replace the rear body harness on a done car? What do I need to remove to get at the harness?  It looks like the kick panel for sure.  Of course I will check the plug there before I proceed any further.   All wires at the headlight switch plug are working correctly and my tail light section operates as it should when I apply independent power.  Thanks for your help.
Logged
BlackoutSteve
Member
***
Posts: 398


138139883
View Profile Email
« Reply #1 on: July 15, 2012, 02:52:19 PM »

Remove kick panel, door scuff plate, rear seat and you may need to remove the and inner 1/4 trim for access to the old loom..

Best to reveal both ends and check continuity with a multimeter before removal.. Could also just be a bad connection.
Logged

Restoring my RHD 69 Jane in Melbourne, Australia.
http://www.usmuscle.com.au/Forum/showthread.php?t=2840
Mac B
Member
***
Posts: 60


View Profile Email
« Reply #2 on: July 15, 2012, 03:02:58 PM »

Thanks Steve, that is what I thought.  Gonna dig into it tomorrow.  I do know there is no juice at the trunk end. Am I correct in thinking the dash end is behind the kick panel?
Logged
BlackoutSteve
Member
***
Posts: 398


138139883
View Profile Email
« Reply #3 on: July 16, 2012, 04:56:08 AM »

The connector isn't but the 1/4 loom is routed behind it..

Edit: Just saw you found and fixed the problem.. Smiley
Logged

Restoring my RHD 69 Jane in Melbourne, Australia.
http://www.usmuscle.com.au/Forum/showthread.php?t=2840
69pace
Member
***
Posts: 364



View Profile
« Reply #4 on: July 16, 2012, 05:40:37 AM »

The connector isn't but the 1/4 loom is routed behind it..

Edit: Just saw you found and fixed the problem.. Smiley

Where was the problem?
Logged

1969 Z-11 350/300 with 4 Speed
Mac B
Member
***
Posts: 60


View Profile Email
« Reply #5 on: July 16, 2012, 06:03:58 AM »

The dashboard end of the body harness was partially separated.  Who knows how it happened but I reconnected it and all is well. Getting the kick panel out is a BEAR!  Of course I scratched it and will be getting a new one.

Logged
Pages: [1] Print 
« previous next »
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.19 | SMF © 2013, Simple Machines Valid XHTML 1.0! Valid CSS!
Page created in 0.092 seconds with 17 queries.