Author Topic: clutch rod  (Read 6968 times)

68rsssrag

  • Member
  • ***
  • Posts: 134
    • View Profile
clutch rod
« on: July 05, 2006, 03:33:48 AM »
As you can see on the maintenance page, i am concerned about the amount of adjustment left (not much) on a new clutch in a 1968 with L35 with M20. I have a 1 piece rod and swivel. The shop manual says uas 2 piece rod on a Camaro V8. Most suppliers say the opposite. My original was 1 pc but who knows.

Any inputs?

Arno

x77-69z28

  • Hero Member
  • *****
  • Posts: 1058
    • View Profile
Re: clutch rod
« Reply #1 on: July 05, 2006, 04:39:33 AM »
the original on both my 67 rs-ss 350 and 69 z28 is the two piece design.
good luck
69 Z/28 X77 burnished brown, 711 int 05A bought in 78
70 Z28 forrest green, green int, M40, bk vinyl roof PROJECT
99 SS hugger orange 6spd NO TTOPS bought new 1 of 54
15 z/28 Arctic white, A/C 505 HP #251

copo

  • Member
  • ***
  • Posts: 98
    • View Profile
Re: clutch rod
« Reply #2 on: July 05, 2006, 07:11:59 PM »
All the B/B 4 speed cars used the 1 piece clutch rod with swivel, the S/B 4 speed cars used a 2 piece clutch rod, this is shown in my 67-70 Camaro GM parts book.

68rsssrag

  • Member
  • ***
  • Posts: 134
    • View Profile
Re: clutch rod
« Reply #3 on: July 06, 2006, 01:58:53 AM »
Hi copo

Very odd the 68 service manual says ALL Camaro and Chevy II V8 use 2 piece and L6 use one piece.  Hmmmm but PN shouldn't lie.

Arno

hotrod68

  • Hero Member
  • *****
  • Posts: 520
  • almost finished
    • View Profile
Re: clutch rod
« Reply #4 on: July 08, 2006, 06:05:14 AM »
The '67-'69s used the same subframe and clutch linkages whether SB or BB from my experience, and all had the same geometry. Back in the day I helped a friend swap a 396 into a '69 where a (gaaaccckkkkkkk) 307 had been, and everything went back flawlesssly using the SB parts with the 396. I've never seen a 1-piece clutch rod with no adjustment on a Camaro--assuming this is the rod between the cross-shaft and the clutch release lever in the bellhousing. Can someone clarify what constitutes a 2-piece clutch rod? I'm confused. By its design the base clutch rod is 2-piece because it has a female body attached to the cross-shaft with a male threaded rod that contacts the release lever. I've never heard of a mechanical 3-piece clutch linkage, which is the 2-piece you you guys suggest. Maybe its semantics. Maybe I'm just dense, but they all had a pushrod from the clutch pedal to the cross-shaft, then an adjustable rod from the cross-shaft to the release fork in the bellhousing. Call it oversimplification, but I still think Arno has mismatched clutch components. There is simply no other reason he has such limited adjustment. Good luck, Arno, and when you resolve this, please post it. I am damn curious.

HotRod'68  1968 SS350 coupe undergoing frame-off resto/rod. 386/350/4.11s
Butternut Yellow    black standard interior

Steve68

  • CRG Member
  • *****
  • Posts: 521
    • View Profile
Re: clutch rod
« Reply #5 on: July 09, 2006, 02:52:33 AM »
Arno

I believe the confusion is with the shop manual using the language " 2 piece rod on a Camaro V8".  It's just to general a statement in this case.  The Parts Books clarify it well.  The Camaro V8 (8 cyl except the 396's) use the 2 piece and the 396's use a one piece design.  6 cyl's also use a 1 piece design.

Steve