CRG Discussion Forum
Welcome, Guest. Please login or register.
Did you miss your activation email?
September 17, 2014, 06:45:50 PM

Login with username, password and session length
Search:     Advanced search
Welcome to the CRG Discussion Forum!
Forum registration problems: Make sure you enter your email correctly and you check your spam box first. *Then* email KurtS2@gmail for help.
104494 Posts in 12235 Topics by 4716 Members
Latest Member: Hgtech
* Home Help Search Login Register
+  CRG Discussion Forum
|-+  Camaro Research Group Discussion
| |-+  General Discussion
| | |-+  68 rocker molding trim clips
« previous next »
Pages: [1] Print
Author Topic: 68 rocker molding trim clips  (Read 1837 times)
tinman75
Member
***
Posts: 81


1968 ash gold rs-ss


View Profile Email
« on: April 07, 2009, 07:04:30 PM »

Anyone ever find a good original style lower rocker molding clip for a 68? It look like the repops are junk. Or does someone have a few originals laying around. Dont need a complete set.
Logged
rat pack
CRG Member
*****
Posts: 221



View Profile
« Reply #1 on: April 07, 2009, 08:47:10 PM »

Are you talking about the ones for the Rally Sport moldings? The standard ones are just like originals. The repros for the RS moldings are very hard to work with, but they do work. I have used others that require a nut to hold them on from the backside for the ones on the doors and quarter panels. If I can find the Auveco part number I will post it later tomorrow along with a picture of the clip..............RatPack.............
Logged

Just keep livin......L I V I N .............
tinman75
Member
***
Posts: 81


1968 ash gold rs-ss


View Profile Email
« Reply #2 on: April 08, 2009, 05:38:45 AM »

Rat pack,
 Thanks for the reply, Yeah, They are for the rally sport, Do you know if they work for the original 1/2 inch hole size on the door? if you could pic and auveco part # I would apreciate it.
Thanks
« Last Edit: April 08, 2009, 05:55:37 AM by tinman75 » Logged
rat pack
CRG Member
*****
Posts: 221



View Profile
« Reply #3 on: April 08, 2009, 02:13:32 PM »

Okay, I just found out today that the clips I have been using are no longer available, but the Auveco clip shown in the picture will work. The clips I had a stash of were made by a company called JOBCO, and they have not made these clips in about 8 years. However, I did find a company that can reproduce them, but I do not know what the cost will be. I had some of the Auveco clips in the bins, and I installed it on a spare molding to see how it fit. No big difference than the JOBCO other than it not having a foam seal which can be easily made. Check with any Auveco dealer for part #2619 for individual clips, or for a box of 25 #12958. These will work just fine. Be sure to use a "washer lock nut" to install them, and the Auveco number for those are 2558. I will post pictures of the other clips on the next reply...........I hope this helps...................RatPack.........................
Logged

Just keep livin......L I V I N .............
rat pack
CRG Member
*****
Posts: 221



View Profile
« Reply #4 on: April 08, 2009, 02:14:41 PM »

Here are some close-ups of the disocontinued clip..........RatPack..............
Logged

Just keep livin......L I V I N .............
tinman75
Member
***
Posts: 81


1968 ash gold rs-ss


View Profile Email
« Reply #5 on: April 09, 2009, 05:27:45 AM »

Thanks for the help!!! I will contact them
Logged
Pages: [1] Print 
« previous next »
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.19 | SMF © 2013, Simple Machines Valid XHTML 1.0! Valid CSS!
Page created in 0.311 seconds with 17 queries.