Author Topic: 69 Z/28 Bumper Guards  (Read 6480 times)

sixt9x33rs

  • Hero Member
  • *****
  • Posts: 980
    • View Profile
69 Z/28 Bumper Guards
« on: February 24, 2009, 02:28:32 AM »
Are the rear Z bumper guards the same size as rear bumper guards for other 69 Camaros?
Are the front bumper guards shorter than the Z rear guards?

Thanks
'69 RS Z/28 65B, 711 Flat hood no spoiler, endura, 4:10 43K miles
69 X77 Z/28 69 69 711 Original Paint Unrestored (Sold)
'69 X66 Convertible 69B 712 auto, (Sold) 44K miles

william

  • CRG Member
  • *****
  • Posts: 3119
    • View Profile
Re: 69 Z/28 Bumper Guards
« Reply #1 on: February 24, 2009, 06:10:05 PM »
They are not "Z" rear bumper guards. Because of lower rear trim height Z/28 equipment included V32 rear bumper guards to comply with federal bumper height standards. They were optional; any 69 Camaro could be ordered with them. I believe they were also included with heavy-duty rear springs.
Learning more and more about less and less...

sixt9x33rs

  • Hero Member
  • *****
  • Posts: 980
    • View Profile
Re: 69 Z/28 Bumper Guards
« Reply #2 on: February 25, 2009, 02:29:08 AM »
They are not "Z" rear bumper guards. Because of lower rear trim height Z/28 equipment included V32 rear bumper guards to comply with federal bumper height standards. They were optional; any 69 Camaro could be ordered with them. I believe they were also included with heavy-duty rear springs.

Thanks
'69 RS Z/28 65B, 711 Flat hood no spoiler, endura, 4:10 43K miles
69 X77 Z/28 69 69 711 Original Paint Unrestored (Sold)
'69 X66 Convertible 69B 712 auto, (Sold) 44K miles

cjm465

  • Member
  • ***
  • Posts: 72
    • View Profile
Re: 69 Z/28 Bumper Guards
« Reply #3 on: February 27, 2009, 12:09:40 AM »
John,

 Can you elaborate more on "lower trim height". Was the rear of the car's height significantly different for multi-leafs vs mono-leaf?

Thanks

william

  • CRG Member
  • *****
  • Posts: 3119
    • View Profile
Re: 69 Z/28 Bumper Guards
« Reply #4 on: February 27, 2009, 01:40:06 AM »
Rear trim height dimension "D" is the distance from the top center of the rear axle to the bottom of the frame rail. Of all variants listed in the manual Z/28 is the lowest at 5.20" nominal. Cars with G31 rear springs are the highest at 6.29", 6.30", 6.38". All measurements are +/- .38".

Z/28 also has the lowest front trim height.

This info is in section O page A10 of the Assembly Instruction Manual.
Learning more and more about less and less...

cjm465

  • Member
  • ***
  • Posts: 72
    • View Profile
Re: 69 Z/28 Bumper Guards
« Reply #5 on: February 27, 2009, 12:46:34 PM »
Thanks William. I don't have The AIM. In the parts inventory for Camaro, was there 2 (or more) sets of multi-leaf, say 4-leaf, that were arched different to determine the ride height with one specific to The Z/28 and another specific to non Z's that required mult-leaf due to options installed? 

Sorry for mistakenly calling you John in my previous question. Too much reading sometimes.

william

  • CRG Member
  • *****
  • Posts: 3119
    • View Profile
Re: 69 Z/28 Bumper Guards
« Reply #6 on: February 27, 2009, 06:13:51 PM »
Not according to our information-all Z/28s received 'BM' rear springs no matter how the car was configured. There were 3 possible front springs.

Other '69s have been known to use a 4-leaf spring but it may have been a different part number/assembly code.

Check the info on this site.


Learning more and more about less and less...

cjm465

  • Member
  • ***
  • Posts: 72
    • View Profile
Re: 69 Z/28 Bumper Guards
« Reply #7 on: February 28, 2009, 01:11:58 AM »
ok thanks

KurtS

  • CRG Coordinator
  • *****
  • Posts: 5884
    • View Profile
Re: 69 Z/28 Bumper Guards
« Reply #8 on: March 02, 2009, 03:47:55 PM »
Kurt S
CRG