Author Topic: what is reasonable value for this 1969 project  (Read 10087 times)

ddc

  • Newbie
  • *
  • Posts: 7
    • View Profile
what is reasonable value for this 1969 project
« on: April 24, 2008, 03:59:54 PM »
I need to get a reasonable range of value for this car as I will be looking to sell soon.

It was produced before the x designation was used on the body plate ID: Sept 1968 Model code 12437 NOR body sequence 103928
Interior trim code: 711 Frost Green Blk Vinyl top     

 It has a Muncie 4 speed, not the rock crusher, Hurst shifter transmission #3925660 It does not appear to have had a spoiler. It has 4 wheel disk brakes,dual exhaust, seats, 5 leaf spring, 12 bolt rear end. I think it is a SS car, don't know about being a Z28 or not. The engine is small block I think. The hood has twin vent stacks either side of centerline. Condition: Front and engine compartment area was removed of most items, except for the front frame & wheels. Gauges off, dash taken down to skeleton. It has door panels, back glass, one side glass other may be inside door. Vinyl top is in good condition. No rust around back glass/trunk area. Floor panels are gone unsure about trunk floor as it is full as is the interior and the doors haven't been opened.
It been dismantled somewhat and I find some things as I go through the garage, engine, hood, transmission. The body back of the firewall is on the car.

I could use some guidance for pricing. Also, I have some pics. Thank you

« Last Edit: April 24, 2008, 04:05:56 PM by ddc »

1968RSZ28

  • Hero Member
  • *****
  • Posts: 6188
    • View Profile
Re: what is reasonable value for this 1969 project
« Reply #1 on: April 24, 2008, 04:46:52 PM »
ddc -

If you post some photos it would help in determining a value.

Paul

ddc

  • Newbie
  • *
  • Posts: 7
    • View Profile
Re: what is reasonable value for this 1969 project
« Reply #2 on: April 24, 2008, 05:06:15 PM »
my pics are not uploading here!
ddc

69 Z11

  • Member
  • ***
  • Posts: 95
    • View Profile
Re: what is reasonable value for this 1969 project
« Reply #3 on: April 24, 2008, 07:28:33 PM »
Very interesting.  I would really like to see the rear axle and discs! 
69 Z11
97 30th SS
Huggers at the Car Show

Flowjoe

  • Member
  • ***
  • Posts: 375
    • View Profile
Re: what is reasonable value for this 1969 project
« Reply #4 on: April 25, 2008, 11:53:08 PM »
Very interesting.  I would really like to see the rear axle and discs! 
Me too

tom

  • Hero Member
  • *****
  • Posts: 1146
    • View Profile
    • Discount Internet Services
Re: what is reasonable value for this 1969 project
« Reply #5 on: April 26, 2008, 01:15:34 AM »
And me.
69 X11 Z21 L14 glide
looking for a 69 export model (KPH) speed
o

ddc

  • Newbie
  • *
  • Posts: 7
    • View Profile
Re: what is reasonable value for this 1969 project
« Reply #6 on: April 26, 2008, 03:24:19 PM »
Do you guys want pics of the 12 bolts and the calipers ? anything else? I haven't taken those but can on Sun. and email them to ya'll.

tom

  • Hero Member
  • *****
  • Posts: 1146
    • View Profile
    • Discount Internet Services
Re: what is reasonable value for this 1969 project
« Reply #7 on: April 26, 2008, 06:27:31 PM »
I would love to see em.

Tom
69 X11 Z21 L14 glide
looking for a 69 export model (KPH) speed
o

69 Z11

  • Member
  • ***
  • Posts: 95
    • View Profile
Re: what is reasonable value for this 1969 project
« Reply #8 on: April 26, 2008, 11:53:56 PM »
Make sure you get a pic of the end of the axle tubes! ;D
69 Z11
97 30th SS
Huggers at the Car Show

Flowjoe

  • Member
  • ***
  • Posts: 375
    • View Profile
Re: what is reasonable value for this 1969 project
« Reply #9 on: April 28, 2008, 08:56:54 PM »
Make sure you get a pic of the end of the axle tubes! ;D
Definitely - why not post them on this thread?

lakeholme

  • Hero Member
  • *****
  • Posts: 2497
  • 68-12D L30/M35
    • View Profile
Re: what is reasonable value for this 1969 project
« Reply #10 on: April 29, 2008, 01:02:22 AM »
my pics are not uploading here!
ddc
You cannot post a picture from Quick Reply, so use tbe Reply button at bottom of this page.  In Reply page, click Additional Options.  An Attach feature will appear.  In Attach, use Browse to find the picture on your computer and attach it.  The pic cannot be any larger than 128KB.  If it is, then use a third party like Photobucket or reduce it.
Phillip, HNR & NCR-AACA, Senior Master, Team Captain, Admin.,
Spring Southeastern Nationals chair, AACA National Director

tom

  • Hero Member
  • *****
  • Posts: 1146
    • View Profile
    • Discount Internet Services
Re: what is reasonable value for this 1969 project
« Reply #11 on: April 29, 2008, 01:39:52 AM »
You can post a photo from quick reply. Click on the preview button, then clck additional options, then you can attach the photo.
69 X11 Z21 L14 glide
looking for a 69 export model (KPH) speed
o

lakeholme

  • Hero Member
  • *****
  • Posts: 2497
  • 68-12D L30/M35
    • View Profile
Re: what is reasonable value for this 1969 project
« Reply #12 on: April 29, 2008, 01:51:41 AM »
Thanks, Tom! Just learned something!  I've been told all this time you could not post a photo from Quick Reply.  But using preview, it gives you the same options as Reply.  Thanks!
Phillip, HNR & NCR-AACA, Senior Master, Team Captain, Admin.,
Spring Southeastern Nationals chair, AACA National Director

Stillwater Camaro

  • Member
  • ***
  • Posts: 60
    • View Profile
Re: what is reasonable value for this 1969 project
« Reply #13 on: May 01, 2008, 12:31:05 AM »
Do you guys want pics of the 12 bolts and the calipers ? anything else? I haven't taken those but can on Sun. and email them to ya'll.
It would a lot easier to email them to me and I will upload them to my webshots account so they can be posted right here.
1967 Camaro SS/RS 350
1966 Chevelle SS 396
1970 Chevelle SS 396
1967 GTO