Author Topic: Solid Lifter Valve / Carburetor Adjustment(s)  (Read 207 times)

69302DZ

  • Newbie
  • *
  • Posts: 5
    • View Profile
Solid Lifter Valve / Carburetor Adjustment(s)
« on: September 12, 2020, 07:08:38 PM »
Stock DZ302, Holley 4053 - While I've had numerous SBCs over the years, I've never owned a solid lifter motor / car until now. I am interested in checking the valve clearance as it seems a tad noisy to me. I read from the Chassis Service manual that the clearance should be 0.030" (intake and exhaust) while hot. I understand the manual to say that they should be adjusted with the motor idling (?). I've adjusted newly assembled hydraulic lifter motors running numerous times but am not clear how this would go with feeler gauges and the solid lifter motor running. Please advise on what the preferred method is - statically with the motor warm? Other? I don't know for a fact that the cam, etc is stock but believe it to be.

Also the car doesn't want to idle warm less than about 1200 rpm. I know the spark plugs were replaced before I purchased it. I need to verify other basics like the points, timing, etc. but am interested in other's thoughts regarding purchasing a rebuild kit for the Holley 4053 if other basic parameters check OK. The external portions of the carb look great but have no idea how old the internal parts are. The inability to lower the idle and have it maintain a normal idle is something I want to correct. Thank you!
'69 Z28 Fathom Green X77
'66 Corvette Nassau Blue L79 Coupe

william

  • CRG Member
  • *****
  • Posts: 2502
    • View Profile
Re: Solid Lifter Valve / Carburetor Adjustment(s)
« Reply #1 on: September 12, 2020, 08:39:28 PM »
Here's the preferred method of mechanical lifter adjustment.

http://www.camaros.org/302valves.shtml

If that is an original carb, it may have mis-matched components or just be worn out. Best to have someone with extensive Holley carb experience examine and rebuild it.

www.z28camaro.com

Learning more and more about less and less...

ko-lek-tor

  • Hero Member
  • *****
  • Posts: 1758
  • someday I'll get one finished
    • View Profile
Re: Solid Lifter Valve / Carburetor Adjustment(s)
« Reply #2 on: September 13, 2020, 02:05:38 AM »
Welcome! Let me just say that the carb will be or has the potential to be more complex a problem. Most advice given in this forum will be based on the assumption that the stock equivalent cam is installed. But a larger duration cam could cause more carb problems. If idle is that high, the idle slots by the throttle plates could be uncovered causing the main circuit to render the idle circuit ineffective. Also the power valve can be dumping fuel if the vacuum is low. There are carb mods to overcome these conditions, but hard to say how to proceed without knowing what cam you have?
James to strangers, Bentley to friends
1969 SS/RS 396 coupe Hugger Orange X22 712 owned since 79
1969 SS 350 coupe LeMans Blue 713 bought in 79(sold)
1969 D.H.COPO replica 4spd. 4.10 posi coupe Daytona Yellow 711 owned since 85

69302DZ

  • Newbie
  • *
  • Posts: 5
    • View Profile
Re: Solid Lifter Valve / Carburetor Adjustment(s)
« Reply #3 on: September 13, 2020, 02:01:37 PM »
Thanks so much for the feedback and advice!
'69 Z28 Fathom Green X77
'66 Corvette Nassau Blue L79 Coupe

z28z11

  • Hero Member
  • *****
  • Posts: 1591
    • View Profile
Re: Solid Lifter Valve / Carburetor Adjustment(s)
« Reply #4 on: September 13, 2020, 08:21:48 PM »
I'd use the adjusting routine suggested in the thread rather than adjusting at idle - I've done that myself many times in the past; even with Erson rocker arm clips to restrict the oil coming out of the pushrods (and blowing all over the place), you really have to be quick and accurate to get it right and keep from scalding yourself with a bunch of hot oil. Never one of my favorite chores, but it was the way I learned to do it. Nigh unto impossible if you have poly locks instead of factory thread locking nuts. You said stock, are you positive the motor has never been "upgraded" ?

Holleys are easier than Quadrajets in my opinion to kit/rebuild. Make sure and use the later ethanol resistant gaskets and needles unless you have the car on a steady diet of non-ethanol gas. Common problems with the 4053's are blown power valves and overtly small accelerator pump squirters, which manifests as an off-idle bog. Easy fix -

Regards,
Steve
1968 Z28 M21/U17 BRG/W
1969 Z28 X77/M20/VE3 LeMans/W
1969 L78 X66/N66 Cortez/BVT
1969 Z11 L48/M35/C60/C06  1949 3100 5wd 235/6

 

anything