Author Topic: 1967 Z for sale ?  (Read 1347 times)

z28z11

  • Hero Member
  • *****
  • Posts: 1559
    • View Profile
1967 Z for sale ?
« on: November 20, 2019, 03:58:25 AM »
Spotted this one, wondered if it was a known car. Good looking color combo even if it's a clone - tag rivets look very new.

https://classiccars.com/listings/view/1201688/1967-chevrolet-camaro-z28-for-sale-in-fort-smith-arkansas-72916?utm_source=Trovit&utm_medium=CPC&utm_campaign=november

Opinions ?

Regards,
Steve
1968 Z28 M21/U17 BRG/W
1969 Z28 X77/M20/VE3 LeMans/W
1969 L78 X66/N66 Cortez/BVT
1969 Z11 L48/M35/C60/C06  1949 3100 5wd 235/6

KurtS

  • CRG Coordinator
  • *****
  • Posts: 5231
    • View Profile
Re: 1967 Z for sale ?
« Reply #1 on: November 20, 2019, 06:26:15 AM »
124377N237116
Kurt S
CRG

67conv6cyl

  • Member
  • ***
  • Posts: 310
    • View Profile
Re: 1967 Z for sale ?
« Reply #2 on: November 20, 2019, 12:23:04 PM »
Car looks nice.....however I have never seen a vin tag on a 67 hinge pillar that far out of kilter?
Maybe vin tag was reattached to a new body? Anybody else think that?

Mike S

  • Hero Member
  • *****
  • Posts: 2561
    • View Profile
Re: 1967 Z for sale ?
« Reply #3 on: November 20, 2019, 01:29:28 PM »
I was wondering the same thing. I thought those holes were pre-punched by Fisher, but maybe I'm wrong.

Mike
67 04B LOS SS/RS L35 Hardtop - Original w/UOIT
67 05B NOR SS/RS L35 Convertible - Restored

Petes L48

  • Hero Member
  • *****
  • Posts: 611
    • View Profile
Re: 1967 Z for sale ?
« Reply #4 on: November 20, 2019, 02:22:11 PM »
I was wondering the same thing. I thought those holes were pre-punched by Fisher, but maybe I'm wrong.

Mike

Looking at UPC 0 Sheet B2 of the 67 AIM it appears that yes, the VIN plate holes were pre-punched into the door pillar.  No drilling instructions shown on that sheet, just the pillar with holes, rivets, and plate.   

67conv6cyl

  • Member
  • ***
  • Posts: 310
    • View Profile
Re: 1967 Z for sale ?
« Reply #5 on: November 20, 2019, 04:04:48 PM »
All of the ones I have looked at seem to be all a little of kilter (however all seem consistently out of plumb in the same manner) this one just looks more then normal of kilter.

Tinkerr

  • Member
  • ***
  • Posts: 270
    • View Profile
Re: 1967 Z for sale ?
« Reply #6 on: November 20, 2019, 10:14:13 PM »
If you were attaching the vin to a NEW body, I would think the last thing you would want to do would be attach it out of kilter and draw attention to it. If you were doing a rebody the hole would already be there from GM.

Mike S

  • Hero Member
  • *****
  • Posts: 2561
    • View Profile
Re: 1967 Z for sale ?
« Reply #7 on: November 20, 2019, 11:42:50 PM »
 The letter L in 4L looks sort of odd. The bottom of the L looks extended. Maybe it's just the way light is reflecting off of it.
67 04B LOS SS/RS L35 Hardtop - Original w/UOIT
67 05B NOR SS/RS L35 Convertible - Restored

Jerry@CHP

  • CRG Member
  • *****
  • Posts: 1462
    • View Profile
Re: 1967 Z for sale ?
« Reply #8 on: December 12, 2019, 03:44:58 PM »
A potential buyer just contacted me about this car this morning.  I have almost 230 cars in the registry now, this car is not in the registry. Not the best photo of the trim tag but I will say that it does have issues.  The L's are also not correct. 

Jerry 

camaronut

  • Member
  • ***
  • Posts: 218
    • View Profile
Re: 1967 Z for sale ?
« Reply #9 on: December 12, 2019, 04:42:58 PM »
Well....someone just bought it.........

67conv6cyl

  • Member
  • ***
  • Posts: 310
    • View Profile
Re: 1967 Z for sale ?
« Reply #10 on: December 12, 2019, 05:24:44 PM »
Well I hope itís not a clone.....Itís way too much for a clone!

rick 67

  • Member
  • ***
  • Posts: 98
    • View Profile
Re: 1967 Z for sale ?
« Reply #11 on: December 12, 2019, 06:03:52 PM »
Well the trunk emblem location is terrible, lid might be a later D80 lid with the holes filled. And the antennae looks a little out of place also.  Site was moving too slow to take a real good look.

 Rick