CRG Discussion Forum
Welcome, Guest. Please login or register.
Did you miss your activation email?
August 20, 2014, 01:50:16 AM

Login with username, password and session length
Search:     Advanced search
Welcome to the CRG Discussion Forum!
Forum registration problems: Make sure you enter your email correctly and you check your spam box first. *Then* email KurtS2@gmail for help.
103272 Posts in 12153 Topics by 4689 Members
Latest Member: merle
* Home Help Search Login Register
+  CRG Discussion Forum
|-+  Camaro Research Group Discussion
| |-+  General Discussion
| | |-+  Originally a 6 cyl, now a SS 396 Clone
« previous next »
Pages: [1] Print
Author Topic: Originally a 6 cyl, now a SS 396 Clone  (Read 1794 times)
1stgenbird
Newbie
*
Posts: 1


View Profile
« on: October 06, 2006, 12:47:05 PM »

Hi Everyone,

I am a new member this forum and happy to have found this site.

There is a 69 SS clone car for sale in my area that I have been looking at.  The VIN decodes as originally being a 6 cylinder car but now has a 396 and a THM400 trans.  The car is in decent condition but needs some cosmetics.  I am trying to find out what issues I might have with a 6 cylinder becoming an 8 cylinder car.  I think the front springs would need to be replaced with heavier duty ones, but someone told me that six cylinders had different wheel lugs, brake line routing, and other things and that 6 cylinder to 8 cylinder clones are not desirable at all.

Any advice would be appreciated.

Thanks,

1stgenbird
Logged
hotrod68
Hero Member
*****
Posts: 520


almost finished

rusticman48@aol
View Profile Email
« Reply #1 on: October 06, 2006, 11:07:23 PM »

If it's a true clone your questions would have already been addressed. 6-banger cars had a 5/16" gas line versus the 3/8" for V-8s to begin with, not withstanding the springs and SS trim and everything else. Not to be short, but it sounds like someone is trying to pull a fast one or just doesn't know any better. Ny 2 cents.
Logged

HotRod'68  1968 SS350 coupe undergoing frame-off resto/rod. 386/350/4.11s
Butternut Yellow    black standard interior
lakeholme
Hero Member
*****
Posts: 2143


*68-12D L30/M35*


View Profile WWW
« Reply #2 on: October 07, 2006, 02:54:31 PM »

Hotrod is right.  Take a look at the rear springs, too.  They should be multi-leaf for a 396. Unless it is a REAL BARGAIN, pass on it and find a better car.
Logged

Phillip
HNR-AACA, Senior Master
Planning 2016 Sentimental Tour, AACA (and restoring a 40 Buick Special for it)
AACA Southeastern Division Spring Meet Chair
"Charlotte AutoFair, presented by the Hornets Nest Region, AACA, is the largest and greatest Collector Vehicle Event in the Southeast USA."
KurtS
CRG Coordinator
*****
Posts: 3171


View Profile Email
« Reply #3 on: October 10, 2006, 11:43:12 PM »

To answer your question, other than the fuel line, the base car is the same.
So it all depends on how good of job they did.
Did they: change axle, change front and rear springs, add disc brakes(assuming it was a drum brake car), etc? If they did it right, it can be hard to tell a clone from a real one.
They could have just installed a BB and drove on. That's just a hillbilly hack then.....
Logged

Kurt S
CRG
Pages: [1] Print 
« previous next »
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.19 | SMF © 2013, Simple Machines Valid XHTML 1.0! Valid CSS!
Page created in 0.079 seconds with 18 queries.