CRG Discussion Forum
Welcome, Guest. Please login or register.
Did you miss your activation email?
April 16, 2014, 08:27:20 AM

Login with username, password and session length
Search:     Advanced search
Welcome to the CRG Discussion Forum!
Forum registration problems: Make sure you enter your email correctly and you check your spam box first. *Then* email KurtS2@gmail for help.
97079 Posts in 11682 Topics by 4578 Members
Latest Member: ronhill
* Home Help Search Login Register
+  CRG Discussion Forum
|-+  Camaro Research Group Discussion
| |-+  Restoration
| | |-+  Did 67 door skin edges have seam sealer?
« previous next »
Pages: [1] Print
Author Topic: Did 67 door skin edges have seam sealer?  (Read 463 times)
Mike S
Hero Member
*****
Posts: 963



View Profile
« on: October 03, 2013, 11:20:27 AM »

   I'm at the stage of readying the car for final primer and was getting the door skin folded edge ready to seam seal. Normally I look at the unrestored '67 I have to get what is correct for finishing but was surprised to see no seam sealer on either door along the folded edge. The skins on the car I am working now have been replaced and I don't remember if there was sealer or not because I assumed the other '67 provided the answer. I looked at a few Camaros in my area and they to have had the skins replaced and sealer applied. The difference between the two '67s I have is one is NOR (being restored again) and the original is LOS (original).
It will be more for visual function because I used the 3M epoxy adhesive to mount the skins and put enough in to flow out the edges when rolled so I know it is sealed inside. I searched the CRG archives but could not find a conclusive answer.

Thank you,
Mike
Logged

67 LOS SS/RS L35 Hardtop - Original w/UOIT
67 NOR SS/RS L35 Convertible - Restored
Sauron327
Hero Member
*****
Posts: 825



View Profile
« Reply #1 on: October 03, 2013, 07:18:11 PM »

No sealer on any original doors I have or had. Sealer may be applied cleanly and minimally, leaving only enough to seal the hem. After paint it would not be detectable. Your use of adhesive would eliminate this step if sqeeze out provided full coverage. Adhesive prevents the usual corrosion. Without it, other hem rust prevention measures are needed. I'd still use cavity wax even with adhesive, just like all cavities.
Logged
Mike S
Hero Member
*****
Posts: 963



View Profile
« Reply #2 on: October 04, 2013, 01:27:57 AM »

 Thank you, Sauron. The epoxy can out the edges when the seams were folded. I was sort of expecting to see the usual factory seam sealer slop on the door.
I'm glad it wasn't used because I like the clean look. I'll look at getting the cavity wax too.

Thanks,
Mike
Logged

67 LOS SS/RS L35 Hardtop - Original w/UOIT
67 NOR SS/RS L35 Convertible - Restored
Sauron327
Hero Member
*****
Posts: 825



View Profile
« Reply #3 on: October 04, 2013, 05:37:52 AM »

3M Rust Fighter I is a cavity wax. SEM and Transtar have it too. Wurth also makes good products. You can buy a 3M 3 foot application wand for a Schutz gun to do the rockers.
Logged
plumL78
Member
***
Posts: 155


View Profile
« Reply #4 on: October 12, 2013, 04:19:53 PM »

Sauron is right Maybe a little solvent to smooth it out and they will look great
Logged
Pages: [1] Print 
« previous next »
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.19 | SMF © 2013, Simple Machines Valid XHTML 1.0! Valid CSS!
Page created in 0.087 seconds with 18 queries.