Author Topic: Exhaust manifold bolts.  (Read 9871 times)

69Z28

  • Hero Member
  • *****
  • Posts: 928
  • 69 X33D80 Z28
    • View Profile
Exhaust manifold bolts.
« on: July 11, 2013, 03:43:32 AM »
Are the exhaust manifold bolts all the same length for the 69 small block and other then the french locks were there any washers used at all? Looking to get new bolts for my 69 Z engine but need this info on washers beforehand. Thanks guys.

GaryC

'UNRESTORED' 1969 Cortez Silver Z28 X33 D80

x77-69z28

  • Hero Member
  • *****
  • Posts: 1058
    • View Profile
Re: Exhaust manifold bolts.
« Reply #1 on: July 11, 2013, 01:42:43 PM »
Same length with thick flat washers
69 Z/28 X77 burnished brown, 711 int 05A bought in 78
70 Z28 forrest green, green int, M40, bk vinyl roof PROJECT
99 SS hugger orange 6spd NO TTOPS bought new 1 of 54
15 z/28 Arctic white, A/C 505 HP #251

69Z28

  • Hero Member
  • *****
  • Posts: 928
  • 69 X33D80 Z28
    • View Profile
Re: Exhaust manifold bolts.
« Reply #2 on: July 11, 2013, 03:38:42 PM »
Same length with thick flat washers


Thanks. Washers on the french looks too correct? Found some engine pics in this post but can't see the bolts to well to tell.


http://www.camaros.org/forum/index.php?topic=10034.0;all
GaryC

'UNRESTORED' 1969 Cortez Silver Z28 X33 D80

Everett#2390

  • Member
  • ***
  • Posts: 148
  • ^Bess
    • View Profile
Re: Exhaust manifold bolts.
« Reply #3 on: July 11, 2013, 03:57:25 PM »
No french locks on center bolts with flat washers, just torque them to 35 ft/lbs.
Outside pairs have flat washers and french locks and torqued to 15 ft/lbs allowing for heat/cold cycles of cast iron manifold(s).
A flashlight is a case for dead batteries.

69Z28

  • Hero Member
  • *****
  • Posts: 928
  • 69 X33D80 Z28
    • View Profile
Re: Exhaust manifold bolts.
« Reply #4 on: July 11, 2013, 11:17:08 PM »
Yeah, gotcha on the french locks not on the center ports. Just needed to know if all the bolts got the washers including the french locks.

Any particular place to get the most correct parts or do you have to order this from there and that from another there? No one seems to carry an all in one kit.
GaryC

'UNRESTORED' 1969 Cortez Silver Z28 X33 D80

Everett#2390

  • Member
  • ***
  • Posts: 148
  • ^Bess
    • View Profile
Re: Exhaust manifold bolts.
« Reply #5 on: July 12, 2013, 12:33:34 AM »
AMK?
A flashlight is a case for dead batteries.

69Z28

  • Hero Member
  • *****
  • Posts: 928
  • 69 X33D80 Z28
    • View Profile
Re: Exhaust manifold bolts.
« Reply #6 on: July 12, 2013, 01:05:47 AM »
GaryC

'UNRESTORED' 1969 Cortez Silver Z28 X33 D80

tmodel66

  • Hero Member
  • *****
  • Posts: 1212
    • View Profile
Re: Exhaust manifold bolts.
« Reply #7 on: July 12, 2013, 02:10:04 AM »
Yeah I got a kit from AMK and included everything including the French locks.
Daniel  
'69 SS 350/4 speed  Fathom Green--POP

69Z28

  • Hero Member
  • *****
  • Posts: 928
  • 69 X33D80 Z28
    • View Profile
Re: Exhaust manifold bolts.
« Reply #8 on: July 12, 2013, 04:13:46 AM »
Yeah I got a kit from AMK and included everything including the French locks.

Hey Daniel, you have number handy? I haven't looked yet but I was going to see what I could find in the 69 AIM if is even in there.
GaryC

'UNRESTORED' 1969 Cortez Silver Z28 X33 D80

Edgemontvillage

  • Hero Member
  • *****
  • Posts: 784
    • View Profile
Re: Exhaust manifold bolts.
« Reply #9 on: July 12, 2013, 05:16:47 AM »
Yeah I got a kit from AMK and included everything including the French locks.

Hey Daniel, you have number handy? I haven't looked yet but I was going to see what I could find in the 69 AIM if is even in there.

Gary, be aware the french locks available from AMK and other parts vendors are made of stainless steel which is incorrect. The originals were stamped untreated steel. GM still sells the steel ones (GM part# 14081241) however the stamping has changed and they are not the correct appearance for our cars. I located used ones, treated them with Evapo Rust and they work well for an unrestored car.   

69Z28

  • Hero Member
  • *****
  • Posts: 928
  • 69 X33D80 Z28
    • View Profile
Re: Exhaust manifold bolts.
« Reply #10 on: July 12, 2013, 07:32:39 AM »
Thanks Lloyd. I wasn't planning on using the stainless pieces. I just need the bolts and washers. Other than the set of french locks that are on my unmolested 46000 mile 69 Impala, I have never seen another set. I can guarantee that there probably isn't a yard within 100 miles of me that would have one old engine in it to rob those locks off of. It seems most of the smaller stuff I need to purchase I have to count on members who might have this stuff stashed away. Well...time for a WTB add on T.C.
GaryC

'UNRESTORED' 1969 Cortez Silver Z28 X33 D80

RS_COPO_Canuck

  • Member
  • ***
  • Posts: 63
    • View Profile
Re: Exhaust manifold bolts.
« Reply #11 on: November 15, 2016, 06:15:50 PM »
For a 69 Z - should the French locks be the rounded or square tab? Also - I think only the center bolts got washers - yes? No?
Thanks

KevinW

  • Hero Member
  • *****
  • Posts: 857
    • View Profile
Re: Exhaust manifold bolts.
« Reply #12 on: November 15, 2016, 08:05:48 PM »
Don't forget A/C cars have two longer bolts for the rear compressor mount :)

elcamino72

  • Member
  • ***
  • Posts: 105
    • View Profile
    • More Information on Camaro Fraud
Re: Exhaust manifold bolts.
« Reply #13 on: November 16, 2016, 10:59:46 AM »
The length of the standard exhaust manifold bolts is 2 1/4".

z28z11

  • Hero Member
  • *****
  • Posts: 1853
    • View Profile
Re: Exhaust manifold bolts.
« Reply #14 on: November 17, 2016, 01:05:17 AM »
Don't forget A/C cars have two longer bolts for the rear compressor mount :)

And a spacer -
1968 Z28 M21/U17 BRG/W 1967 Chevy ll Nova SS 
1969 Z28 X77/M20/VE3 LeMans/W
1969 L78 X66/N66 Cortez/BVT
1969 Z11 L48/M35/C60/C06  1949 3100 5wd 235/6