31
General Discussion / 68 fuel pump
« on: September 15, 2018, 09:04:07 PM »
Did any 1st gens come factory with an electric
in line fuel pump ?
in line fuel pump ?
News:
Welcome to the CRG Discussion Forum!
Classified ads are not allowed on the forum.
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
32
Decoding/Numbers / What color was it ?
« on: September 09, 2018, 05:22:48 PM »
Why no exterior color code on cowl tag
Of my 05B , 1968
Any help
On this ?
Of my 05B , 1968
Any help
On this ?
33
General Discussion / Manual convertible top
« on: September 08, 2018, 08:09:13 PM »
Just bought a 68 rs/ss convertable,
and the manual top wont go all the way open, seems to
Be some interference with the back glass or the frame bow at the top of the glass!!
Any ideas ?
Thank You
and the manual top wont go all the way open, seems to
Be some interference with the back glass or the frame bow at the top of the glass!!
Any ideas ?
Thank You
34
Originality / Wiper switch
« on: November 07, 2017, 01:11:54 PM »
How rare is this wiper switch ?
https://rover.ebay.com/rover/0/0/0?mpre=https%3A%2F%2Fwww.ebay.com%2Fulk%2Fitm%2F222702409689
https://rover.ebay.com/rover/0/0/0?mpre=https%3A%2F%2Fwww.ebay.com%2Fulk%2Fitm%2F222702409689
35
Originality / 1969 clock usage
« on: November 07, 2017, 01:06:44 PM »
What trim level or etc dictated what cars got a dash clock ?
36
Restoration / Reverse Lockout
« on: September 06, 2017, 10:33:39 PM »
Hello All !!
I am interested in installing the reverse
lockout linkage on my 69 BB RS/SS 4 spd ,
It seems there are a few variations of this and
I am not sure which version belongs in my car ,
I do know that there are 3 holes in the frame
at the mounting location
But only two of the holes are threaded .
Any help or direction is greatly appreciated !
Thanks
Jim
I am interested in installing the reverse
lockout linkage on my 69 BB RS/SS 4 spd ,
It seems there are a few variations of this and
I am not sure which version belongs in my car ,
I do know that there are 3 holes in the frame
at the mounting location
But only two of the holes are threaded .
Any help or direction is greatly appreciated !
Thanks
Jim
37
General Discussion / Shifter adjustment Help
« on: April 18, 2017, 07:47:11 PM »
Hello,
I need your advice ,
When I got my car a BB 69 RS/SS non numbers
Car, it had a Blatantly wrong shifter ....
So I decided to buy a correct rebuilt
3138 shifter assembly, then I got a
supposedly correct aftermarket BB Linkage with
Mounting plate set up.
Everything installed and shifts great ,
except when I go into reverse , it seems that
The shifter travel is to long , pulling the reverse
Lever to a full 90 degrees from the neutral"down" position
Then that angle is such that I can't shift out of reverse.
Thanks for any help you can offer.
Jim
I need your advice ,
When I got my car a BB 69 RS/SS non numbers
Car, it had a Blatantly wrong shifter ....
So I decided to buy a correct rebuilt
3138 shifter assembly, then I got a
supposedly correct aftermarket BB Linkage with
Mounting plate set up.
Everything installed and shifts great ,
except when I go into reverse , it seems that
The shifter travel is to long , pulling the reverse
Lever to a full 90 degrees from the neutral"down" position
Then that angle is such that I can't shift out of reverse.
Thanks for any help you can offer.
Jim
40
Decoding/Numbers / Muncie ,What do I have?
« on: February 24, 2017, 07:44:09 AM »
Can Any one tell me exactly what transmission I have
42
General Discussion / Radiator hose part #
« on: February 03, 2017, 11:35:34 PM »
69 BB 4 sos, Can someone tell me what the
GM part number is for the upper
and lower radiator hoses ?
Thanks
Jim
GM part number is for the upper
and lower radiator hoses ?
Thanks
Jim
44
Restoration / 4 speed Shifter hole location ?
« on: January 25, 2017, 02:05:03 PM »
Looking for your help !
Think about installing the trans hump repair panel.
What is the exact location and dimension
of the shifter hole in the trans hump
For a 69 BB with a Muncie 4spd
Thanks
Jim
Think about installing the trans hump repair panel.
What is the exact location and dimension
of the shifter hole in the trans hump
For a 69 BB with a Muncie 4spd
Thanks
Jim