Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - MooneyDriver

Pages: 1 2 [3] 4 5 ... 7
31
General Discussion / Re: New guy, New project ' 67
« on: February 08, 2015, 06:35:30 AM »
so whats the trick to getting the piece of quarter out of here? Or should I have left a lip and butted it up? Might do that on the drivers side....  Thoughts?







ALOT of spot welds on this, I just went at it with a grinder on each weld, I counted like 86 just in that center section!




Had to put the new back piece on for fun! Its not a big deal, but gives ya the feeling of the new to come!


Under part doesnt touch it, I knew it was pushed in some, Ill bang on that once the quarter is sitting in place.

32
General Discussion / Re: New guy, New project ' 67
« on: February 08, 2015, 06:34:45 AM »
ok, been a few months since Ive had time to get any solid time on it, between the cold WX (no heat in the shop), and having to put a new motor in the inlaws exploder, I finally got to spend 5 hrs on it today, here what the damage I did.

Pass quarter is off, rear panel is off, piece between the trunk and window is off, fuel tank is out.












33
General Discussion / Re: in case anyone is interested
« on: December 24, 2014, 03:58:50 PM »
pink? eww

34
General Discussion / Re: New guy, New project ' 67
« on: December 05, 2014, 03:47:58 PM »
if it helps any, here is the stampings on the rear quarters




What are you trying to determine?

35
General Discussion / Re: New guy, New project ' 67
« on: December 05, 2014, 02:38:29 AM »

36
General Discussion / Re: New guy, New project ' 67
« on: December 04, 2014, 04:54:45 AM »
Where should I look?

37
General Discussion / Re: New guy, New project ' 67
« on: December 04, 2014, 01:26:26 AM »



38
General Discussion / Re: New guy, New project ' 67
« on: December 03, 2014, 09:02:43 PM »
Ill snap those after work, I should have read my notifications, I was just there, haha.

39
General Discussion / Re: New guy, New project ' 67
« on: December 02, 2014, 10:14:24 PM »
Quote from: KurtS on December 02, 2014, 09:57:32 PM
John,
Do you have the original decklid for the car?
What are some of the dates from the seat belts?
I'd be curious on the axle and trans codes whenever you get them - no hurry. :)

Thanks!

I do, but the car was backed into something, and the decklid is a little goobered up, as well as the back of the car.  The aftermarket lid actually fit just as good, plus has the spots for the rear spoiler to get drilled.



Here is the origional decklid on the back of the trailer

40
Restoration / Re: door top on 67 w/ std interior
« on: December 02, 2014, 03:48:29 PM »
Quote from: L78 steve on December 02, 2014, 04:07:52 AM
This answers the The GM jam decal question I have. What is the build date on this 67?



41
Restoration / Re: door top on 67 w/ std interior
« on: December 02, 2014, 12:52:13 AM »
Hope this helps!











42
Restoration / Re: door top on 67 w/ std interior
« on: December 01, 2014, 10:56:45 PM »
Yessir, in about an hour Ill get shots!

43
Restoration / Re: door top on 67 w/ std interior
« on: December 01, 2014, 09:59:38 PM »
Origional door paint on mine



Ill try to get some better ones after work.

44
General Discussion / Re: New guy, New project ' 67
« on: November 25, 2014, 03:44:47 PM »
Perfect, thanks

45
General Discussion / Re: New guy, New project ' 67
« on: November 25, 2014, 05:57:02 AM »
cool, Ill have to see if mine has them or not from the factory.

Pages: 1 2 [3] 4 5 ... 7
anything