Messages

16

Originality / Re: Factory motor mounts

« on: November 11, 2015, 02:21:55 PM »

Thanks I had checked that out earlier but it doesn't  mention the numbers for the engine mounts-thanks!
Keep on Cruising!
Dave

17

Originality / Factory motor mounts

« on: November 11, 2015, 02:51:12 AM »

I picked up a box full of camaro parts from a guy-I got a mint set of 3950113/114 69 bb frame mounts and a pair of nos in gm boxes #3990916 engine mounts-1  nos # 6258154 in gm box mount and 2 mint /used #330973 engine mounts-any idea which mounts were installed at the factory? Thanks in advance!
Keep on Cruising!!!
Dave

18

Originality / Re: grooved cowl air cleaner

« on: October 18, 2015, 12:19:51 AM »

I think the only difference from a factory installed one to the over the counter service replacement one is the vent tube shape-factory ones have the 90 degree bend while the service replacement ones have the two 45 degree shape
Keep on Cruising!
Dave

19

Decoding/Numbers / Stewart Warner Gear Reduction

« on: September 13, 2015, 09:10:52 PM »

Cleaning out my toolbox in the garage-found  a Stewart Warner gear/speedo reduction unit has .9743 Y stamped on it-any idea what it is from?Thanks in advance!!!!It may be from a 70 gm pick up-not sure.
Keep on Cruising!!
Dave

20

General Discussion / Re: Stolen Z Found

« on: August 18, 2015, 10:58:25 PM »

My buddy had a nice mid 80's blazer all done up that he drove on nice /dry days in the winter as well as all summer-he and his family were ice skating at a local outdoor rink when he saw his truck being driven away.Hard to chase someone on skates-they found it 3 days later all burnt!
Keep on Cruising!!!

Dave

21

Originality / #20037597 inside window handles with black knobs

« on: August 08, 2015, 06:22:20 PM »

I know most came with clear knobs and are expensive to find NOS  but what would a set of NOS black knob handles fit and be worth? Thanks in advance!
Keep on Cruising!
Dave

22

Originality / Original Cowl Induction Throttle Arm

« on: August 08, 2015, 01:03:44 PM »

Is there any way to tell an original or gm piece from a reproduction-was at a friends house and he had a cowl induction throttle arm-he wasn't sure if it was a reproduction or not-the only stamping I saw was  "C" stamped on it-whats a gm one worth?Thanks in advance!
Keep on Cruising!

Dave

23

Originality / Re: "W" stamped on the cowl induction flange

« on: August 21, 2014, 03:33:27 PM »

Thanks for posting the pictures Bryon-noticed other parts with the "W" stamping on them-I have a holley heat shield that has the W stamping.
Keep on Cruising!!!

Dave

24

Originality / Re: "W" stamped on the cowl induction flange

« on: August 20, 2014, 02:47:32 AM »

I am out of town till Thursday-will post a picture then-thanks!
Keep on Cruising!
Dave

25

Originality / "W" stamped on the cowl induction flange

« on: August 19, 2014, 06:37:03 PM »

 I replaced the 69Z28 cowl induction flange on my chevelle with a NOS correct notch/cut off type correct for chevelles-the camaro one I have had for many years it has a "W" stamped on it -I take it it is a manufactures stamp-any idea who made these. Only idea I had many Winters-but I know they were a foundry-are these camaro flanges worth any more than the chevelle ones? Thanks in advance!
Keep on Cruising!

Dave

26

Originality / Re: Did all cowl induction air cleaners have the vent tube??

« on: July 11, 2014, 01:43:46 AM »

Thanks-wonder what it is off of-it had the correct camaro flange with th "W" stamped on it-and seems to be the same diameter as a cowl air cleaner-and a flat bottom!

Dave

27

Originality / Did all cowl induction air cleaners have the vent tube??

« on: July 10, 2014, 05:51:03 PM »

I went to look at some bumoers for my sons 67RS.Started talking with the guy and he said he had a cowl induction air cleaner that he took off a 69 Camaro 30 years ago. It apperars to be a flat bottom one but when I flipped it over there was no vent tube? The snout looked like a Gm one-maybe it was for something else. Sorry my camera died so no pictures. May go back though. Thanks in advance for all your inut!

Dave

28

Originality / Re: Did all 69Z28 cowl induction breathers have a flat bottom ?

« on: September 14, 2013, 02:57:52 AM »

Thanks everyone for your input-the  4 dimple flame arrestors also had "GM" stamped on them-(although it wwas hard to read)I have a couple NOS ones -boxes dated 1982 -if anyone is looking for one!
Dave

29

Originality / Did all 69Z28 cowl induction breathers have a flat bottom ?

« on: September 12, 2013, 08:33:23 PM »

Did all the 69Z28 cars have the flat bottom cowl induction ait breathers ?I know the ridge bottom ones were service replacement-Just curious if they had  switched anytime -thanks for any input!
Dave

30

Decoding/Numbers / Shifter Rods I.D

« on: July 31, 2013, 11:54:10 PM »

First off I want to say this is a great site!Been lurking here a while-finally signed up-Many know me from the Chevelle forums -but I have start working on my sons 67 RS 327 -it is a roller right now-anyway it came with a m21 tranny(don't think it is the original one) -in a box I found a shifter-the rods have #6004,6005,6065 stamped on them-any idea what they are off of?Thanks in advance!!!!!
Keep on Cruising!!!!!!
Dave