Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - toddstoys

Pages: [1]
1
Originality / Re: RPO U17 - firewall hole size
« on: February 26, 2013, 02:14:54 AM »
  My car has all of the components for a functional hood with complete flat bottom air cleaner, solenoid, pedal switch, pedal bracket for the switch, relay, wire harness etc. Also has non-SS hood springs.  I know the previous owners history back to 1970, just two previous owners and they say that how the car was.  Not possible to locate original owner. I've owned the car since 1974. The original cowl hood had some serious rust issues and a replaced it with a new OTC from a local Chevy dealership about 25 years ago. So I lost the evidence with the hood date stamp. Its very possible the original owner had it installed by the dealership upon vehicle delivery, again its a early 01D dated car. I read that flat bottom air cleaners were only early cars up to about Aug. 69. Late cowl induction cars has a ridge bottom air cleaner like on a Chevelle.
I hope someone else replies with information with the wire harness hole in not to specification location, or any Van Nuys car with similar issues.   

2
Originality / Re: RPO U17 - firewall hole size
« on: February 25, 2013, 02:33:32 PM »
Guys simular issue with 1969 SS build date 01D  Van Nuys car. I have C60 air conditioning option and have the 1" hole for the vacuum lines in the correct location.  However I have the ZL2 cowl induction option also and the wire harness is routed through the same hole.  They both share the hole in the fire wall. Anybody out there on the forum have piculiar issues with fire wall penetrations from early Van Nuy cars?

3
General Discussion / Re: Zl-2 Cowl Hood Production
« on: February 19, 2013, 03:12:58 AM »
OK.... just got home and measured its a 1" hole. It is for #9 on the drawing for C-60 air condition vacuum lines. The cowl induction wire harness is routed through that hole also. It has been like that since I purchased the car in 1974. I attached picture from CRG with a white arrow pointing to the location. The cowl set up may have been dealer installed..... I don't know ????  Have you ever seen several harness or vacuum sharing penetrations in the firewall ? Thanks guys for you help.

4
General Discussion / Re: Zl-2 Cowl Hood Production
« on: February 18, 2013, 06:02:53 PM »
OK.......I'll try to expain without pictures.  If you were standing in front of the car looking at the break booster, the location of the vacuum check valve (in a straight line)  the piercing is on the firewall  2 1/2" below that check valve. Also I failed to mention its a air conditioned car with a console. I do not have that much clearance like in your picture.  I will send pictures ASAP, won't be untill later. Thanks for your help, really appreciated.

5
General Discussion / Re: Zl-2 Cowl Hood Production
« on: February 18, 2013, 04:07:04 PM »
I failed to mention that it not and Rally Sport and I do not have a gauge package.  Its an automatic trans car. Of course I want to have some evidence that it was factory installed.  I could not have been drilled or punched with the brake booster in place, also it could not have drilled or punched from under the dash.  I think highly unlikely that someone at a dealership removed the power brake booster to drill  or punch a 3/4" hole for the grommet. The penetration is clean as if it was punched.  My car has all of the components for a functional hood complete flat bottom air cleaner, soleniod, pedal switch, pedal bracket for the switch, relay etc. Previous owners history back to 1970 was as is. Not possible to locate original owner. Back then guys just wanted the cowl induction hood and and not interested if it was functionable. Who was restoring a Camaro back in 1970 back to origional. I hope someone else replies with information with the wire harness hole in not to specification location. Where are the guys with the high end fully loaded 69 camaros?  :)  I'll try to post a picture of the location of the harness hole. Thanks for the reply.

6
General Discussion / Re: Zl-2 Cowl Hood Production
« on: February 17, 2013, 09:26:11 PM »
Hello guys I'm new to this forum, I have been reading the forum for several years but this topic spiked my interest. I have been owning a 1969 camaro SS 350 for 39 years. Its a 01D   (early Van Nuys car) production Daytona yellow with a cowl induction hood.  The air cleaner is the flat bottom and have all the wiring harness that is correct. I know the two previous owners and they said the hood was on the car when they bought it.  I do not know who the original owner was. I have one issue is that the wiring harness hole is not in the location above the fuse block, in fact its on the opposite side of the the brake booster. The hole is drilled where a dimple was from the photos I have seen. It could not have been drilled out with the brake booster installed. Also it has the non SS hood springs. The original cowl hood had some serious rust issues and I purchased a new one about 25 years ago from the a local Chevy dealership. So I do not know what the stamp on the drivers side of the hood was. The big question I have is............Do any of you guys know of any early cowl equipped cars that the wire harness hole in a different location?  Maybe some of the early cowl equipped cars from Van Nuys are the same. 

Pages: [1]
anything