CRG Discussion Forum
Welcome, Guest. Please login or register.
Did you miss your activation email?
November 27, 2014, 03:55:42 PM

Login with username, password and session length
Search:     Advanced search
Welcome to the CRG Discussion Forum!
Forum registration problems: Make sure you enter your email correctly and you check your spam box first. *Then* email KurtS2@gmail for help.
106634 Posts in 12432 Topics by 4790 Members
Latest Member: gmein
* Home Help Search Login Register
  Show Posts
Pages: [1] 2 3
1  Camaro Research Group Discussion / General Discussion / Re: 50 Z/28's For Sale ??? on: December 26, 2012, 07:17:29 PM
Could have at least put the temperature sending unit on the correct side Tongue Tongue Tongue Tongue Tongue
2  Camaro Research Group Discussion / General Discussion / Re: This Car Has "Wrong" Written All Over It. on: December 16, 2012, 05:49:21 PM
I don't know, guys, this cat says he has been to EVERY car auction........ Roll Eyes
3  Camaro Research Group Discussion / Originality / '69 Driveshaft question on: September 30, 2012, 07:56:35 PM
I have read I need a 49 9/16" driveshaft for my '69 with 350/Turbo 350 and 12 bolt.A friend has one 49" and yoke just under 5". Can I use this and change the yoke to one of the 5.5" ones? Thanks Huh
4  Camaro Research Group Discussion / Maintenance / Re: Opinion needed-engine/tranny first or front end? on: September 04, 2012, 10:44:43 AM
Thanks guys
5  Camaro Research Group Discussion / Maintenance / Re: '69 horn wiring on: September 03, 2012, 09:37:12 AM
Well that explains it, I should be used to this crap by now >:(who has the correct ones?
6  Camaro Research Group Discussion / Maintenance / Re: '69 horn wiring on: September 03, 2012, 07:32:20 AM
Yeah Steve, I got all that, but the spring and contact don't fit in the sleeve when you put the little grommet with the wires in it....for now I left the contact pin out, I 'm wondering if the contact is too long....
7  Camaro Research Group Discussion / Maintenance / Opinion needed-engine/tranny first or front end? on: September 02, 2012, 08:33:37 PM
Had to remove the right front fender and skirt, bumper, grille,valance, etc to install A/C box....seems to me it would be easy to remove radiator support,put engine and tranny together on the floor and slide them right in, then put the sheetmetal back on.....chime right in please
8  Camaro Research Group Discussion / Maintenance / '69 horn wiring on: September 02, 2012, 08:27:40 PM
Could someone please explain how the 2 wires from the horn buttons on a '69 2 spoke wheel connect to the column? I have a spring and a metal button also.....this car is making me dumb Shocked
9  Camaro Research Group Discussion / Maintenance / Re: '69 blower fan replacement on: September 02, 2012, 08:25:30 PM
Yeah, pulled the fender and skirt, etc. wasn't too bad, had it all apart in about 45 minutes,thanks fellas
10  Camaro Research Group Discussion / Originality / Dumb questions about interior rear side panels... on: August 27, 2012, 07:56:38 PM
I didn't take my '69 apart so I don't know what missing if anything. Is there anything that attached the rear panel to the car? Right now it just hangs there....are there supposed to be armrests? Hard to believe that the rear seat holds it in by itself..... Huh
11  Camaro Research Group Discussion / Maintenance / '69 blower fan replacement on: August 21, 2012, 08:13:26 PM
Could someone tell me the simple way to replace the blower fan? My car was painted and the front end put on without the A/C box and blower fan installed. Chassis manual says pull lower fender out 6"!!!! after loosening the rear skirt bolts. Don't mind spending the time but didn't want to take the fender off unless I had to......thanks guys
12  Camaro Research Group Discussion / Originality / Re: Color for horn relay & e-brake brackets on: August 17, 2012, 04:45:00 PM
Yes the ones attached to the leaf spring mounting plates
13  Camaro Research Group Discussion / Originality / Color for horn relay & e-brake brackets on: August 17, 2012, 04:06:23 PM
Need the colors for horn relay and the 2 rear emergency brake cable brackets......thanks
14  Camaro Research Group Discussion / Originality / '69 TH350 shifter mounting hardware on: July 29, 2012, 09:31:19 AM
There are some big holes in the floor of my car where the shifter gets mounted, about 7/16".....what is the correct hardware? Thanks
15  Camaro Research Group Discussion / General Discussion / Re: Poor quality reproduction crap.... on: July 29, 2012, 09:18:14 AM
OK, thanks for the info....where are the triangular reinforcements located?
Pages: [1] 2 3
Powered by MySQL Powered by PHP Powered by SMF 1.1.20 | SMF © 2013, Simple Machines Valid XHTML 1.0! Valid CSS!
Page created in 0.127 seconds with 19 queries.