CRG Discussion Forum
Welcome, Guest. Please login or register.
Did you miss your activation email?
April 17, 2014, 07:20:10 PM

Login with username, password and session length
Search:     Advanced search
Welcome to the CRG Discussion Forum!
Forum registration problems: Make sure you enter your email correctly and you check your spam box first. *Then* email KurtS2@gmail for help.
97139 Posts in 11686 Topics by 4578 Members
Latest Member: ronhill
* Home Help Search Login Register
  Show Posts
Pages: 1 [2]
16  Camaro Research Group Discussion / Restoration / Re: Parking Lights will not turn off on: February 27, 2013, 08:11:43 AM
Mark, this appears to be an ignition switch - do you happen to have this for a 68 Light Switch? Thanks!
17  Camaro Research Group Discussion / Restoration / Re: Parking Lights will not turn off on: February 26, 2013, 03:49:02 PM
I think so  - haven't found it yet - think it might be at the storage shed across town.
18  Camaro Research Group Discussion / Restoration / Re: Parking Lights will not turn off on: February 26, 2013, 02:59:45 PM
Mike and Lynn - thanks for the suggestions.

Mike - I have done some searching under every related topic I can think of, but cannot find the string on the misplaced wire. Any other thougths?

Lynn, The side markers are also on. I have the AIM and am looking at it. I replaced all the harnesses (for big $ to boot) with American Wire harnesses. Everything appeared to be high quality, but either I crossed a wire somewhere or the harness has a problem. Unfortunately, I had reassembled almost everything on the car before finding this problem.

I have searched to find a picture of an original RS switch connector to see if the harness pins are the same as the American Wire connector......but so far, no luck here either.
19  Camaro Research Group Discussion / Restoration / Parking Lights will not turn off on: February 23, 2013, 11:14:30 AM
I have just replaced my wiring harnesses. Now, my parking lights will not turn off. I have check the ground on the driver side radiator core and at the instrument cluster. I thought the switch must be bad, so I just replaced it - no difference. Any one run into this?
20  Camaro Research Group Discussion / Restoration / Re: 68 tilt steering column too long on: February 15, 2013, 09:34:29 PM
Well my first thought was correct - I was an idiot. I did not realize it is a collapseable column. While pulling the steering wheel off, I must have lengthened the column. by standing it on end and pushing down, I has able to shorten the column enough to work.
21  Camaro Research Group Discussion / Restoration / Re: 68 tilt steering column too long on: February 14, 2013, 11:26:55 AM
Gary, I will take a look when I get home, but the brace can only go on one-way - there is one hole on the left of the column and two on the right (the hole closest to the firewall has the shim). Let me know if I am missing your point.

I am wondering if I should take the bolt out of the coupling so I can slide it back more to get room - then, see if I can bolt it up under the dash and then try to re-position the coupling prior to bolting it to the rag joint. I've R&Red the columns several times with no issues - not sure why I am having this problem with the p/s gear box.
22  Camaro Research Group Discussion / Restoration / Re: 68 RS Conv Rear Harness Routing Help on: February 13, 2013, 08:53:52 PM
Mike, there should be a hole in the wheel tub flange for the plastic tree wiring harness stay. this should help you line it up.
23  Camaro Research Group Discussion / Restoration / 68 tilt steering column too long on: February 13, 2013, 08:49:55 PM
Guys, I must be missing something (or am just an idiot). I am adding power steering (got the Saginaw gear from a 68 bird). I am trying to install my original tilt column, but it seems nearly an inch too long when I try to line-up the three holes for the the under dash studs. Any one run across this?
24  Camaro Research Group Discussion / Restoration / Re: Upper Dash Windshield Bracket - 68 RS Conv on: December 04, 2012, 12:31:29 PM
Lynn, I sent you an e-mail with pics George Clark provided - these and the otherposts should give you everything you need.
25  Camaro Research Group Discussion / Restoration / Re: Quarter Window Well Water Drain on: November 10, 2012, 05:44:16 PM
Thanks Mike - - I found it and cleared it. It was blocked with crud.
26  Camaro Research Group Discussion / Restoration / Re: Console bracket & U-joint on: November 10, 2012, 11:36:34 AM
Chick, my 68 was natural with a little primer overspray.
27  Camaro Research Group Discussion / Restoration / Quarter Window Well Water Drain on: November 10, 2012, 11:33:43 AM
I recently got my 68 back from having the quarters replaced. As I am installing the quarter windows, I notice that I do not see any way for water that gets in through the window to drain. Are there supposed to be drain holes in the bottom of this area? If so, does any one have a photo of what they look like?
28  Camaro Research Group Discussion / Restoration / Re: 68 RS Conv Rear Harness Routing Help on: October 24, 2012, 08:36:43 PM
Awesome Ed - I have a fold-down rear seat and power top as well - this is just what I need! Thanks!
29  Camaro Research Group Discussion / Restoration / 68 RS Conv Rear Harness Routing Help on: October 24, 2012, 07:06:28 PM
I am in the middle of my restoration and am having a brain cramp on the correct routing of the rear harness. The area I am not sure of is from the passenger compartment into the trunk. Does it go through the area for the convertible top mechanism, or does it go outside that area along the seat back frame? If anyone has any pictures, I'd be grateful!
30  Camaro Research Group Discussion / Restoration / Upper Dash Windshield Bracket - 68 RS Conv on: October 04, 2012, 01:17:18 PM
Help - I screwed-up!

I replaced the upper dash with an aftermarket unit from NPD (after a little work, it fit well). Yesterday, I went to put the windshield in and found the aftermarket piece did not have holes for the 2 windshield support brackets or the 8 support clips. No problem you say - just take the measurements off the old one? Well, this is where I find that my scrap guy was too quick - the old one is gone. Does anyone have the locations.....or any other ideas?
Pages: 1 [2]
Powered by MySQL Powered by PHP Powered by SMF 1.1.19 | SMF © 2013, Simple Machines Valid XHTML 1.0! Valid CSS!
Page created in 0.091 seconds with 18 queries.