CRG Discussion Forum
Welcome, Guest. Please login or register.
Did you miss your activation email?
March 04, 2015, 11:10:22 PM

Login with username, password and session length
Search:     Advanced search
Welcome to the CRG Discussion Forum!
Forum registration problems: Make sure you enter your email correctly and you check your spam box first. *Then* email KurtS2@gmail for help.
110450 Posts in 12759 Topics by 4892 Members
Latest Member: jvc7450
* Home Help Search Login Register
  Show Posts
Pages: 1 ... 17 18 [19] 20 21 ... 30
271  Camaro Research Group Discussion / Restoration / Re: Correct Centre Link finish on: June 04, 2013, 07:27:42 AM
I blued mine also along with arm that goes to frame. On mine the arm was clean enough you could see the dark finish. There was a nos one on eBay showing the color also.very easy to do and cheap!
272  Camaro Research Group Discussion / Decoding/Numbers / Re: DZ Stamp on: May 23, 2013, 11:40:25 AM
Block is 4 days after mine. Mine has an unusual date cast of a109. It's a 661 also. My off-road  am has the 141 stamp also
273  Camaro Research Group Discussion / Restoration / sway bar bushings 69 Z on: May 18, 2013, 10:13:42 AM
I got 2 different sets of sway bar bushings from hbc and don't like either. My 03D has the fingered bracket. First I got the hole acts like at least 23/32 and I will have to trim since its too tall. The other is for the earlier bracket and not close. I am hoping to find something closer than these. Who knows these could be Moogs not sure. Anyone find any they liked?
274  Camaro Research Group Discussion / Restoration / Re: Correct 69 Z/28 Coil Springs on: May 12, 2013, 11:27:45 AM
I had a set of small block springs from HBC and the car sat almost as high as it does with the motor out. I looked up david pozzi's site and it has alot of good info with moog part numbers.  If your doing a z, they sat lower than a small block car.
http://www.pozziracing.com/camaro_spring_info.htm
275  Camaro Research Group Discussion / Originality / Re: 1969 Control Arm Alignment Shims on: May 05, 2013, 12:21:43 PM
My car has 12800 on it but drag racer/first owner messed with somethings. I have found neat inspection marks . This week I had the rear axle cover off and it had a lot of blue paint markings. Springs were a greenish yellow. I think a lot of my bolts are original but some hard to read. I have wondered if my car was stored someplace damp and if the guy was on stone roads. He's around but I have only talked to his son and he doesn't have a lot of info.
276  Camaro Research Group Discussion / General Discussion / Re: 1969 Z/28 questions on: May 05, 2013, 12:09:34 PM
Poly bushings have been known to squeak. Would be a lot of work to change them out.
I agree on paint, matching numbers should be the correct color. I wouldn't buy a car in a color I didn't like matching numbers or not anyway
277  Camaro Research Group Discussion / General Discussion / Re: 1967 "Pilot" cars on: May 03, 2013, 11:54:11 AM
Any of these these ever appear or did they meet the crusher?
278  Camaro Research Group Discussion / Originality / evaporust on axles on: May 02, 2013, 11:33:00 AM
Had some crude on end of a me shafts and sat the hub end in evaporust for a day. Rinsed them off and found a big blue paint dawb on the edge of the hub. Runs from one stud to the next. Evaporust is neat stuff
279  Camaro Research Group Discussion / Originality / Re: 1969 z28 rear brake backing plates on: April 21, 2013, 11:23:12 AM
Thanks Gary. Our springs are the same color. What gets me, I have some parts from hbc and springs are not the same color. I got wheel cylinders and knew they weren't delco but the 2 they sent don't match each other! Mine are fine inside and rebuilding them. I got a rebuild kit from ricks and their pictures look like the one they use for front matches my rears. Guy said sometimes the pics are wrong. What I got is like the picture, no rubber ends on springs. Very annoying. These places should know. I think the white number on my adjusters is 384. Wonder what that means. You can't mess with number it wants to come right off.
280  Camaro Research Group Discussion / Originality / Re: 1969 z28 rear brake backing plates on: April 21, 2013, 10:16:40 AM
Thank you. My drums had never been off and welded themselves go the hub. I heard you could back them off but no hole .
281  Camaro Research Group Discussion / Originality / 1969 z28 rear brake backing plates on: April 20, 2013, 09:08:28 PM
Haven't found exactly what I'm looking for.
I noticed on eBay plugs for an adjuster hole on the backing plate. I got some parts from HBC and the plugs were included. My backing plates don't have a hole for them?
Also not sure what they are called but the arms,levers that are involved with the parking brake seem to be plated with the parts dealers. Mine show no signs of gold after cleaning with evaporust. We're they bare metal?
282  Camaro Research Group Discussion / Decoding/Numbers / Re: What carb date for my 06A early June Z on: April 15, 2013, 04:56:34 PM
I have a 954 and been looking almost a year for a late January/ February.  Tough to find and not paying 1500!
283  Camaro Research Group Discussion / Originality / Re: color of front leaf spring bracket? on: April 14, 2013, 05:04:05 PM
Thanks John
Was going to get my axle assembled and hope to get it under the car this week and found those with no paint on them!! too many parts here I guess. 
284  Camaro Research Group Discussion / Originality / Re: Z28 grill and tailpanel emblem question. on: April 14, 2013, 09:07:39 AM
One of my fronts is a dark grey instead of silver but the same part number. Weird stuff
285  Camaro Research Group Discussion / Originality / Re: Z28 grill and tailpanel emblem question. on: April 14, 2013, 08:17:28 AM
Jerry's book shows 3958642 as the front. His rear number is 8701333 which is on a box I have but emblem is different
Pages: 1 ... 17 18 [19] 20 21 ... 30
Powered by MySQL Powered by PHP Powered by SMF 1.1.20 | SMF © 2013, Simple Machines Valid XHTML 1.0! Valid CSS!
Page created in 0.142 seconds with 18 queries.