Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - 67conv6cyl

Pages: 1 ... 12 13 [14]
196
General Discussion / Re: small bumper guards under rear bumper
« on: March 27, 2012, 01:52:05 AM »
Original bumpers do not look like they ever had anything bolted to them, could it be that 6 bangers did not get them?

Paul

197
General Discussion / Re: small bumper guards under rear bumper
« on: March 27, 2012, 01:28:23 AM »
Did all Norwood cars have them, I ask because I have a very original car that I a sure did not have them, I have old pictures of car and the bumpers on car are original and never touched..........Paul

198
General Discussion / small bumper guards under rear bumper
« on: March 27, 2012, 12:48:22 AM »
Can anybody let me know about the small rear bumper guards under the bumper on a 67, I read on this sight that they were standard although I have an 04A car and it never had them?

199
6-cylinder Camaros / Re: Is there a market for a '67 6cyl engine?
« on: March 21, 2012, 01:12:34 AM »
Do you know if it has  power steering?  I need the bracket that mounts the cradle to the block on a 67 six cyl, I would also buy the whole engine if I lived closer however I live on east coast.

Paul

200
Originality / Re: Seat adjuster knob
« on: March 20, 2012, 12:13:30 AM »
I miss understood my tilt forward knob for back seat entry is chrome plated metal with set screw, my knob for front leg ajustment is push on chrome plated hard plastic (magnet dose not stick) this is a factory original unrestored 67.

Paul

201
Originality / Re: Seat adjuster knob
« on: March 19, 2012, 10:41:48 PM »
My original 67 has metal

Paul

202
6-cylinder Camaros / Re: Front Swaybar
« on: March 06, 2012, 04:17:40 AM »
build date for my 250 is 04A has factory sway bar.

203
General Discussion / Re: 67 power steering bracket help
« on: February 28, 2012, 03:34:51 AM »
Bob,
It does however I can't see it, the part #  is on engine side of harmonic balancer
Paul

204
General Discussion / Re: 67 power steering bracket help
« on: February 27, 2012, 12:56:31 AM »
Bob,
Yes thats right one groove was not used , (page 260) of the AIM this is a 250 six car.  230 six cars (page 209) I belive have single groove
Paul

205
General Discussion / Re: 67 power steering bracket help
« on: February 26, 2012, 11:28:43 PM »
Bob, the harmonic balancer has 2 grooves. It is the factory original.
Paul

206
General Discussion / Re: 67 power steering bracket help
« on: February 26, 2012, 07:34:33 PM »
Thanks Bob, I have that manual that's were I found the part #s that I listed, did I list the wrong ones? The Assembly manual I have is 25 years old however the part #s should be the same. Paul

207
General Discussion / Re: 67 power steering bracket help
« on: February 26, 2012, 04:43:50 AM »
Yes I am adding it, I bought all the other parts needed such as pump with pulley, water pump pulley, power steering gear box, hoses & pump cradle. I just need the bracket that holds cradle to the block, pump to alternator bracket & two grove alternator pulley  all the parts I bought where off another 67  6 cyl and are correct for my car. For some reason the owner before me ordered this car new  with a power top but no power steering.  I am saving all the original parts because this car is so original.

208
General Discussion / Re: 67 power steering bracket help
« on: February 26, 2012, 03:03:40 AM »
The original alternator pulley has what looks like the fan connected to it. The car did not have power steering from factory, does part# 3871253 include fan? This is a very very original unrestored low mileage car with some odd options  (for a six) so I would like to use the right parts with out permanently altering anything.

209
General Discussion / 67 power steering bracket help
« on: February 25, 2012, 05:02:47 PM »
I can't seem to find these parts anyware the part #'s are 3891598, 3838446, 3843346 they brackets and a alternator pulley for a 67 can any body help?

210
6-cylinder Camaros / Re: Front Swaybar
« on: February 23, 2012, 11:52:07 PM »
My 67 convertible 250 6cyl came with factory sway bar

Pages: 1 ... 12 13 [14]