CRG Discussion Forum
Welcome, Guest. Please login or register.
Did you miss your activation email?
April 20, 2014, 05:54:54 AM

Login with username, password and session length
Search:     Advanced search
Welcome to the CRG Discussion Forum!
Forum registration problems: Make sure you enter your email correctly and you check your spam box first. *Then* email KurtS2@gmail for help.
97237 Posts in 11693 Topics by 4578 Members
Latest Member: ronhill
* Home Help Search Login Register
  Show Posts
Pages: 1 ... 11 12 [13] 14
181  Camaro Research Group Discussion / General Discussion / Re: vehicle certification label on: December 07, 2010, 11:39:58 AM
http://www.ecsautomotive.com/
182  Camaro Research Group Discussion / General Discussion / Re: vehicle certification label on: December 07, 2010, 11:30:59 AM
The company is ELC or ECL or something like that. I have the info at home. They also do them for the Chyslers. Maybe it will jog someone's memory
Joe
183  Camaro Research Group Discussion / Restoration / looking for someone who purchased a yellow houndstooth int from Al Knoch on: December 02, 2010, 11:56:33 AM
If anyone out there has purchased a yellow 1969 interior from Al Knoch, I would like to ask you a few questions pleaase
Thanks, Joe
184  Camaro Research Group Discussion / General Discussion / Re: 69 camaro LH door on: November 15, 2010, 02:35:39 PM
If I'm not mistaken it was in Aug of 69 the LH door was changed. Jerry McNeish talks about it in his books. The LH door has 2 impressions where the new Federal sticker went. Mine is 08E & has that door....Joe
185  Camaro Research Group Discussion / Originality / Re: 67 power feed wire on: November 03, 2010, 08:23:17 AM
MY first reply was mostly correct except fot the placement of the hole for the wire that goes through the firewall , at least for 68/69. I don't have an assm manual for a 67 to check. C06 show the harness placement & A31 say to refer to C06....Joe
186  Camaro Research Group Discussion / Originality / Re: 1968 Tail pipes on: October 30, 2010, 05:11:25 PM
They're straight cut & oval on all the ones I've seen.....Joe
187  Camaro Research Group Discussion / Originality / Re: 1967 printed circuit on: October 28, 2010, 11:27:09 AM
Thanks for everybody's help. He discovered a stray ground. Thanks, Joe
188  Camaro Research Group Discussion / Originality / 1967 printed circuit on: October 22, 2010, 06:15:47 AM
Is the printed circuit on the back of the inst cluster the same for tach & non tach?
Thanks, Joe
189  Camaro Research Group Discussion / Originality / Re: 67 power feed wire on: October 20, 2010, 08:20:33 AM
I gave you the wrong info. The wire going through the firewall is next to a ground strap below the wiper motor....Sorry.
Joe
190  Camaro Research Group Discussion / Originality / Re: 67 power feed wire on: October 19, 2010, 02:44:25 PM
Unless 67 is different the 68/69 for power windows and/or power top there should be a wire going through the firewall. There's a wire (black) that comes from the horn relay & goes to the circuit breaker that's attached to the firewall behind the m/c power booster. The wire coming from the circuit breaker (orange w/blk) goes through the firewall. It has a small grommet attached to it. There's a dimple in the firewall where you would need to drill. It's discussed in the assm manual. If I'm not mistaken it's near the upper LH bolt for the pedal mount. I can look tonight if that would help....Joe
191  Camaro Research Group Discussion / Decoding/Numbers / Re: 69 Rear End Code Stamping on: October 15, 2010, 03:55:32 PM
I've seen a few over the years that were stamped on both axle tubes. Some I've seen at almost 12:00 position. Happy hunting, Joe
192  Camaro Research Group Discussion / Restoration / Re: 4 spd shifter hole for a 69 on: October 08, 2010, 10:28:28 AM
Thanks for everybody's imput. I've forwarded the info to a guy who's replacing the entire floor pan. A problem we don't have in Tucson....Joe
193  Camaro Research Group Discussion / Restoration / 4 spd shifter hole for a 69 on: October 07, 2010, 04:49:35 PM
I have a piece of a floor that I cut out a 67 or 68 years ago. I don't remember if it was automatic or std from the 67 or not. My question is how close could it be for use on a 69? Was the hole always in the same spot for 3spd/ 4spd trouugh out the 67/69?
Thanks, Joe
194  Camaro Research Group Discussion / General Discussion / Re: VCCA on: September 24, 2010, 01:56:58 PM
I'm a member but never had anything judged...Joe
195  Camaro Research Group Discussion / General Discussion / Re: Does a short block include . . . on: September 24, 2010, 09:12:17 AM
Normally neither will come with a balancer. Performance engines might if they were balanced that way
Pages: 1 ... 11 12 [13] 14
Powered by MySQL Powered by PHP Powered by SMF 1.1.19 | SMF © 2013, Simple Machines Valid XHTML 1.0! Valid CSS!
Page created in 0.09 seconds with 18 queries.