Messages

601

Originality / Re: 9428047 rivet

« on: November 13, 2020, 01:31:53 AM »

Thanks James & Jim. I guess I need to find an 1969 a/c car that hasn't been taken apart...Joe

602

Originality / 9428047 rivet

« on: November 12, 2020, 07:34:53 PM »

Does anybody have the specs on a 9428047? Is it a pop rivet or something else? In the 1969 AIM, it calls for 2 to hold the heater control valve & 2 to hold a bracket to the fender well that holds the main a/c hose. Ref; C60 D6.5 & C60 D5. The currant part is a pop rivet.Thank you, Joe

603

Restoration / Re: Seat bun (foam) recommendation

« on: November 12, 2020, 02:53:46 PM »

Hi Bentley. Here is a link. I went with the recommendation from here. Fit well & the guy doing the seats liked them. Made in the USA....Joe

http://www.camaros.org/forum/index.php?topic=16166.msg146183#msg146183

604

General Discussion / Re: International Camaro Club

« on: November 11, 2020, 08:07:10 PM »

One of my cats chews on cardboard also...Joe

605

General Discussion / Re: International Camaro Club

« on: November 11, 2020, 12:02:57 AM »

Read hear Bill....Joe

http://www.camaros.org/forum/index.php?topic=15818.0

606

Originality / Re: clips

« on: November 05, 2020, 02:26:20 AM »

Thanks James. That also would make since...Joe

607

Originality / Re: clips

« on: November 04, 2020, 05:25:39 PM »

Thank you Mike. That was my guess but I guess my short hand is too short
Joe

608

Originality / clips

« on: November 04, 2020, 04:18:10 PM »

I'm putting my 69 back together after paint. These 2 clips were in the bag I had marked a rocker tin so they are the galvanized plates under the carpet & sill plates. Can anybody tell where they went? Maybe held the antenna cable for a rear antenna car? Thank you, Joe

609

Restoration / Re: 1969 Body Tail Light Wiring Harness, Rally Sport

« on: November 03, 2020, 08:23:03 PM »

I sent my harnesses to AAW so I wouldn't have to go through this problem. There is also some major changes in the starter & headlight harness that had to be done. They even put my original tags back. They're building harnesses to the latest upgrades which isn't what I want for my car. Some of the connectors aren't made like the originals....Joe

In hindsight sending your original wiring to AAW was a brilliant plan, let them sweat transferring the connectors and sockets . Will likely do the same on the next project!

It's probably a walk in the park for them.....Joe

610

Restoration / Re: 1969 Body Tail Light Wiring Harness, Rally Sport

« on: November 03, 2020, 01:26:35 AM »

I sent my harnesses to AAW so I wouldn't have to go through this problem. There is also some major changes in the starter & headlight harness that had to be done. They even put my original tags back. They're building harnesses to the latest upgrades which isn't what I want for my car. Some of the connectors aren't made like the originals....Joe

611

General Discussion / Re: Pace car registry

« on: October 29, 2020, 07:01:28 PM »

To update what I posted above:
The db has 650+ 69 pace cars in it with about 70 of those from Van Nuys.
And about 175 Z10's. So much for the people that said there were about 100-150 Z10's built.

That collection of facts didn't just happen over night either...Joe

612

Originality / Re: Early N66 SS rim car with original jacking instructions

« on: October 25, 2020, 05:11:44 AM »

All the center caps I ever had used hex bolts to hold the retainer on the back side...Joe

613

Originality / Re: Early N66 SS rim car with original jacking instructions

« on: October 24, 2020, 11:07:00 PM »

Why is this screw driver part of this option?...Joe

614

Originality / Re: wheel well molding bolt finish. any survivors?

« on: October 23, 2020, 01:42:29 PM »

My observation is zinc if it has moldings. Phosphate if it doesn't. It's shown in AIM Z21 A1....Joe

615

Originality / Re: 1969 side marker bezels

« on: October 20, 2020, 01:45:08 AM »

Thanks Jim. I'm probably over thinking this. It could be as simple as 2 manufactures. I was just looking for other input...Joe