481
Decoding/Numbers / Re: came across a 4C built Z28 yellow with yellow hounds tooth trim
« on: May 27, 2021, 03:00:10 AM »
X66. Trying to finish it for MCACN..Joe
News:
Welcome to the CRG Discussion Forum!
Classified ads are not allowed on the forum.
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
482
Decoding/Numbers / Re: came across a 4C built Z28 yellow with yellow hounds tooth trim
« on: May 27, 2021, 02:05:21 AM »Hi Joe,Mine was built 8/28/1969....Joe
your car sounds amazing with the Parchment(white) roof Yellow/Yellow
mine is a 76B 714 09C built car.....John
483
Decoding/Numbers / Re: came across a 4C built Z28 yellow with yellow hounds tooth trim
« on: May 27, 2021, 01:34:45 AM »
If it was equipped with a factory vinyl, there would've been a letter following the color code. B is black. Mine is 76E 714. Vinyl tops were an option....Joe
484
Decoding/Numbers / Re: came across a 4C built Z28 yellow with yellow hounds tooth trim
« on: May 26, 2021, 11:20:59 PM »
There's an 02B car known shipped in March....Joe
485
General Discussion / Re: Seat mounting holes
« on: May 21, 2021, 05:46:59 PM »
I just looked a L527 (didn't get the whole VIN) which is March. Both sets of seat holes....Joe
486
Restoration / Re: 1969 L78 Smog set up
« on: May 21, 2021, 03:29:58 AM »
Can you post the link?...Joe
487
General Discussion / Re: Original dealer info for 1st gens is available
« on: May 19, 2021, 10:22:09 PM »
Interesting list. Some of those numbers were used in the 30s. It was used in part of the body serial number then, like 12AE or 6CC were the series of the car built at that plant.....Joe
488
General Discussion / Re: Seat mounting holes
« on: May 19, 2021, 01:58:40 PM »In Joe's picture look like the front holes were use not the rears.Since this isn't the 1st time my seats have been out, I don't know which holes it was in from the factory. It doesn't really matter as long as I can drive the car. (I was built a little lower to the ground
) I was just using what Ed had posted. I've had this car since 1981 & this restoration I was paying a little closer attention to things I've seen here. This is the cars 2nd restoration.....Joe
489
General Discussion / Re: Seat mounting holes
« on: May 18, 2021, 07:04:22 PM »
I compared the bolt holes in my 68 & 69. The 68 has 4 holes that line up with the forward holes on the 69. According to what Ed posted you would be moving the seat forward. This would indicate GM was using the rear set of bolt holes as the default mounting in 1969....Joe
490
General Discussion / Re: Seat mounting holes
« on: May 17, 2021, 06:19:25 PM »
Thank you Ed....Joe
491
General Discussion / Re: Seat mounting holes
« on: May 16, 2021, 12:59:35 PM »
Here's a picture of mine.....Joe
492
Decoding/Numbers / Re: eBay X44
« on: May 15, 2021, 09:48:06 PM »
At least he says it a clone. Clone of what, I don't know but it has breaks. Wonder if it has brakes also....Joe
493
Originality / Re: Power window firewall piercing 1969
« on: May 15, 2021, 10:35:06 AM »
Thank you James....Joe
494
General Discussion / Re: Seat mounting holes
« on: May 15, 2021, 12:04:27 AM »Putting my car back together & noticed the seat mount on the floor has 8 threaded bolt holes for each bucket seat. When did that start?...Joe
Build date of car? 08/28/1969. I'll get a picture tjis weekend...Thanks, Joe
Pics?
495
General Discussion / Re: Seat mounting holes
« on: May 14, 2021, 02:53:06 AM »
My friend's 01B LA doesn't have the the new pattern. Just an interesting observation.....Joe