CRG Discussion Forum
Welcome, Guest. Please login or register.
Did you miss your activation email?
April 20, 2014, 04:07:24 PM

Login with username, password and session length
Search:     Advanced search
Welcome to the CRG Discussion Forum!
Forum registration problems: Make sure you enter your email correctly and you check your spam box first. *Then* email KurtS2@gmail for help.
97277 Posts in 11694 Topics by 4578 Members
Latest Member: ronhill
* Home Help Search Login Register
  Show Posts
Pages: 1 ... 79 80 [81]
1201  Camaro Research Group Discussion / General Discussion / clean up and polishing Windshield and rear glass molding on: December 09, 2009, 11:09:59 PM
I have good molding that is original to my '69SS.  I would like to keep it but as you probably know it is "white" dull. I have tried several polishes and wax and cream and I am just wasting my time and money. Can anyone tell me where to send it to get it polished out  like new?  I am about to do a  face lift and spruce it up a little and I just can't get it to shine like it's supposed too.

Thanks 





Daniel
1202  Camaro Research Group Discussion / Decoding/Numbers / Re: I need help with X 55 numbers and little steel plate from the glove box on: December 07, 2009, 08:20:24 PM
Thanks for all the replys but I am still having a problem figuring out what some of it means. I mean some of the stuff is confusing. If you have this certain number it might be Z87 or something and if you have this number you have Z24 or something else. Then you get into subsections of this section and this certain number belongs to this other subsection  and around and around I go. But anyway I am still just as lost.
But THANKS
Daniel
1203  Camaro Research Group Discussion / Mild Modifications / Re: MOTOR MOUNT STRAPS on: December 02, 2009, 02:03:47 PM
I don't know if this makes sense but I broke the bolts that held it to the manifold.  I ended up going with solid steel mounts.  A little vibration at idle but it held that puppy down. I had to do something drastic cause I almost went under a semi-truck with a stuck throttle and it almost caused my heart to stop.  LOL
1204  Camaro Research Group Discussion / Decoding/Numbers / Re: Help with build date? on: November 26, 2009, 09:35:47 AM
Just a little information.  I know it won't help you but I have an  07 A  build date  like you and my VIN is  667804. According to your VIN 607452  they had to build  60,352 cars in July.  I am not saying it's impossible but to me thats a lot of cars.  Hope you have luck with your search.
1205  Camaro Research Group Discussion / Decoding/Numbers / Re: I need help with X 55 numbers and little steel plate from the glove box on: November 25, 2009, 08:34:37 PM
Thanks and here it is:
  
    C        124379N667804
    7         BM0630G            T0626HA
                 133                  P9H24
  
    
1206  Camaro Research Group Discussion / Decoding/Numbers / I need help with X 55 numbers and little steel plate from the glove box on: November 25, 2009, 07:30:43 PM
I have a '69 SS with X 55 cowl plate.  I figured out some of it but what does  L 48  stand for.   Also I can't figure out what the numbers are on the little steel plate that was in the dash with the owners manual.  Everything is printed backwards and I can't make hide nor hair of it. Can I post it and get some help with that?  I have it in hand so I can copy it any time.
 
  Thanks 
  Daniel
1207  Camaro Research Group Discussion / Maintenance / Re: Blower Fan to Heater Core... on: November 25, 2009, 08:17:10 AM
You might have a bad switch.  Been a long time since I changed one but I think they have a resistor on them for high settings and they burn out or get wet and blow. Anyway that blower motor don't know the diiference if it's running on 4 speed switch  or 10 speed.
1208  Camaro Research Group Discussion / Maintenance / Re: at high revs it stalls and dies out please help. on: November 25, 2009, 08:01:14 AM
Did it ever run right after you got it put together?  If it did you might have a bowl full of trash and the float is stuck.  Something might have got in the needle and seat  allowing enough fuel to idle.  You might have trash in the accelerator pump blocking fuel flow.  Last but not least you have a major vacuum leak.  Did the gasket cover all the ports on the intake?  I have seen  gaskets that are for several applications and sometime I didn't check the coverage on intake til something like this happened.
1209  Camaro Research Group Discussion / Restoration / Re: Matching Numbers '69 SS restore HELP on: November 24, 2009, 10:19:08 PM
Thanks  Big Al. I'll give it a try when time comes.  Any other tips on  do's or don'ts  would be a Great Help. I would like to put it back as close to "showroom" new as possible.   
1210  Camaro Research Group Discussion / Restoration / Matching Numbers '69 SS restore HELP on: November 24, 2009, 04:25:25 PM
I am a newbie and have read some great stuff on this site and I need some HELP.  I am about to start work on a '69 SS with matching numbers. Would it be best to use all the original parts that are useable or is it OK to use repo to make it look newer?   The dash pad is not cracked but is slighty warped. Does anybody know how to get the warp out or should I replace it?  As of now the only thing that I see to replace is carpet, door panels, and that piece of card board behind the back seat.  That piece has a single speaker in it.  Is that factory or did someone just put one speaker in.  Would anybody recommend  Rick's or Yearone for parts?   
  ANY HELP would be greatly appreciated

Pages: 1 ... 79 80 [81]
Powered by MySQL Powered by PHP Powered by SMF 1.1.19 | SMF © 2013, Simple Machines Valid XHTML 1.0! Valid CSS!
Page created in 0.076 seconds with 18 queries.