CRG Discussion Forum
Welcome, Guest. Please login or register.
Did you miss your activation email?
July 30, 2014, 04:09:03 AM

Login with username, password and session length
Search:     Advanced search
Welcome to the CRG Discussion Forum!
Forum registration problems: Make sure you enter your email correctly and you check your spam box first. *Then* email KurtS2@gmail for help.
102481 Posts in 12091 Topics by 4669 Members
Latest Member: paulmanta
* Home Help Search Login Register
  Show Posts
Pages: 1 ... 7 8 [9] 10 11 ... 14
121  Camaro Research Group Discussion / General Discussion / Re: TH350 VIN stamp on: December 13, 2011, 08:01:56 AM
Thanks Paul you are correct. That is the car vin.#.
I was not thinking, period. I was so busy looking for a casting# that I, well du!
Hit me last night. Thats why Ed didn't know what I was asking.  So it is a
matching trans. Thanks for the help!

122  Camaro Research Group Discussion / General Discussion / TH350 VIN stamp on: December 12, 2011, 09:10:47 PM
Can anybody tell me what a TH350 vin # 19N607953 is out of?Huh?
123  Camaro Research Group Discussion / Maintenance / Re: HELP!! Starter problems on: August 11, 2011, 10:09:05 PM
Yes they are. Yes it is. Paper clip clearance  at tooth tip on three points all the same.
124  Camaro Research Group Discussion / Maintenance / Re: HELP!! Starter problems on: August 09, 2011, 11:09:45 PM
Have somewhat similar problem that started after a starter bendix change. At times, numerous times the bendix will not go into the flywheel or mesh when attempting to start. You have to turn the key to start a few times, during which you hear the bendix slap the flexplate but not engage because it didn't mesh.
I have shimmed, shimmed, shimmed until..... I have had the bendix changed again, used all parts of another starter, but bendix.
Checked the flywheel with all seeming to be OK?? Missing something. Any thoughts?
Note: I attempted to knive the edge of the bendix to remove any flat spots on the outer edge and it seemed to help some. But still not solving problem.
125  Camaro Research Group Discussion / Originality / Re: Radiator support seal L48 A/C on: August 09, 2011, 10:36:15 PM
luv2sixty9
Sorry have not checked post for while.  Have seal but need clips. do you want to sell need all nine. Or if you want to sell both contact me at cbcrick69@yahoo.com
126  Camaro Research Group Discussion / Restoration / A/C Compressor on: July 18, 2011, 09:20:13 PM
Looking for a rebuild kit for the A-6 Compressors. Anybody know a source for parts to rebuild them?
127  Camaro Research Group Discussion / Originality / Re: Radiator support seal L48 A/C on: July 01, 2011, 10:47:04 PM
What is the original PN for the clips?
128  Camaro Research Group Discussion / Originality / Re: Radiator support seal L48 A/C on: July 01, 2011, 09:35:24 PM
Mark do you know where one can get the metal ones like your pic?
129  Camaro Research Group Discussion / Originality / Radiator support seal L48 A/C on: June 29, 2011, 10:47:47 PM
Looking for some info on the fasteners for the seal across the top of the radiator support on L48 A/C cars. Any pictures or posts on here? Any suggestions on where to get them?
I Have the seal, but can not find any thing relating to the clips other than the assy manual.
bc
130  Camaro Research Group Discussion / Maintenance / Re: Rear main seal leak on: May 04, 2011, 09:35:23 PM
Will check it out and appreciate the input. Anybody else have anything to add, please do.
131  Camaro Research Group Discussion / Maintenance / Re: Rear main seal leak on: April 28, 2011, 05:13:37 PM
Cost of the seal is the least of my concern. I do not want a leak and after all this, as I said, I want this next time to solve the problem.
 Sounds like the #BS-118291 is the best way having what one might call a backup lip?  Or would one suggest the #2900?
132  Camaro Research Group Discussion / Maintenance / Re: Rear main seal leak on: April 24, 2011, 03:18:31 PM
Well.......does anybody have a remedy for a still slightly dripping rear 2 pc seal?
Down to random drip.
After 2 not doing anything else until listening to a number of suggestions.
Do they make a different style of the old two peace?
133  Camaro Research Group Discussion / Maintenance / Re: Rear main seal leak on: March 09, 2011, 08:37:46 PM
Just got it running again and no leaks yet. Gray Fel-pro 2 piece seal was the problem!!!
This crank has never been touched other than being polished just before assembly. So anybody installing a new rear 2 pc seal, I suggest that you roll it in and check that the lips have a good amount of pressure or crush on them before installing the rear cap.


Brad
134  Camaro Research Group Discussion / Maintenance / Re: Rear main seal leak on: March 09, 2011, 07:52:40 PM
Thought that I might have got it in backwards, dropped pan and it was in right, so now what, went and picked up another seal, this one was blue in color and looked to be a little heavier seal. Rolled it into place and it had more crush than the other. The gray one had next to not pressure on the crank.
135  Camaro Research Group Discussion / Maintenance / Re: Rear main seal leak on: March 09, 2011, 02:55:39 PM
Sure did.
Pages: 1 ... 7 8 [9] 10 11 ... 14
Powered by MySQL Powered by PHP Powered by SMF 1.1.19 | SMF © 2013, Simple Machines Valid XHTML 1.0! Valid CSS!
Page created in 0.077 seconds with 18 queries.