CRG Discussion Forum
Welcome, Guest. Please login or register.
Did you miss your activation email?
April 18, 2014, 08:44:37 AM

Login with username, password and session length
Search:     Advanced search
Welcome to the CRG Discussion Forum!
Forum registration problems: Make sure you enter your email correctly and you check your spam box first. *Then* email KurtS2@gmail for help.
97153 Posts in 11687 Topics by 4578 Members
Latest Member: ronhill
* Home Help Search Login Register
  Show Posts
Pages: 1 [2]
16  Camaro Research Group Discussion / Restoration / Re: Original plating on: January 10, 2011, 01:16:16 PM
BlackoutSteve .The next one you have looks like B-13388 on pg 146, but it's not blue.
Where did that clip come from off the car?
I have a 69 AIM and I don't see the corresponding GM number.                                                                                                                                                                                                                                                                                                                                                                    Both clip picks are the same clip.Clip was on fuel line along with about 6 or 7 others. One seams a light blue.
17  Camaro Research Group Discussion / Restoration / Re: Original plating on: January 10, 2011, 03:34:14 AM
E Mail sent to brake boosters. com. (Blackoutsteve) I am real sure my brake line clips are green the clip above in the pick was on fuel line. I understand what 3/8 means but what is the other mark in the pic. and thanks for steering me to Brakebosters.com. I can send a few things to him.
18  Camaro Research Group Discussion / Restoration / Original plating on: January 08, 2011, 06:35:04 PM
Can any one recommend a place that can replate fuel line and brake line clips.  Thanks Ron.
19  Camaro Research Group Discussion / Mild Modifications / Re: Factory tack vs MSD on: October 29, 2010, 12:28:45 AM
Thanks a bunch Steve & Wayne. I did not stop to think it just might be as simple as calling MSD. Duh.
20  Camaro Research Group Discussion / Mild Modifications / Factory tack vs MSD on: October 24, 2010, 02:53:35 AM
How and what would be needed to run a msd dist, with a factory tack?
21  Camaro Research Group Discussion / General Discussion / Re: Edelbrock C396 QJ and C396 BBC intake on: October 15, 2010, 12:31:14 AM
Can vaguely remember, while working in a marina Years and Years ago, "Think"I remember something like that on a Mercury inboard boat engine. I am not 100% though. The place Had a few open engine 26-30 foot jet boats I did some work on also. Stil Was back early 70s.
22  Camaro Research Group Discussion / Decoding/Numbers / Re: Voltage regulator 8J on: October 13, 2010, 08:53:31 AM
Wow. Thanks much Kurt. I think i would have bet against that. Also wounder if you received my Email about this car? Thanks again.
23  Camaro Research Group Discussion / Decoding/Numbers / Voltage regulator 8J on: October 13, 2010, 01:14:06 AM
Hi. Question for all. I have a 11D 69 that had a 8J 515 voltage reg on it. could that possibly be the original or is that just to early to be possible? Or given the fact that electrical parts went bad all the time was it probably a junkyard replacement.
24  Camaro Research Group Discussion / Decoding/Numbers / Re: Any markings on wood stering wheel. on: October 07, 2010, 04:06:14 AM
Thanks all. And thanks for the link Kurt. Final Conclusion is ... Fake... The welds are real nice but the grain is alot like the second pick, and the spokes are dark spotty like that too. However no cracks so i will probably use it. Seams real skinny to grip though. The hub is what had me going that's  orig GM.
25  Camaro Research Group Discussion / Decoding/Numbers / Any markings on wood stering wheel. on: October 06, 2010, 01:19:07 AM
I have a walnut steering wheel with alot of wear on it. And center (stainless?) is turning black or corroding slightly. How does a guy tell a orig. from a repo. Can't post pick haven't figured out how to downsize yet. And thanks everyone involved for a great site. Hope i asked this in the right forum?   Ron
26  Camaro Research Group Discussion / Originality / '69 fold down rear seat on: July 28, 2010, 01:47:19 AM
I need the screws that hold the fold down rear seat back frame to the upholstery frame. I can't find any information on finish and size of the screws.  The seat is at the upholstery shop so I can't get a look at what size I need. Can anyone help me out?  Thanks, Ron Undecided
27  Camaro Research Group Discussion / Decoding/Numbers / Re: Question about Fisher Body date on: February 12, 2010, 01:52:51 PM
If this helps,I have an 11d car. VIN comes up 189 cars AFTER November's end of the month VIN. I asked a local Corvette restoration shop about this very question. They told me that 11d was the last week. That the 1st & 2nd were the last week of Oct. I then wondered if Corvette was labeled in the same guide lines. Sorry for the late reply, I don't get on here very often.
Pages: 1 [2]
Powered by MySQL Powered by PHP Powered by SMF 1.1.19 | SMF © 2013, Simple Machines Valid XHTML 1.0! Valid CSS!
Page created in 0.084 seconds with 18 queries.