CRG Discussion Forum
Welcome, Guest. Please login or register.
Did you miss your activation email?
October 21, 2014, 02:15:18 AM

Login with username, password and session length
Search:     Advanced search
Welcome to the CRG Discussion Forum!
Forum registration problems: Make sure you enter your email correctly and you check your spam box first. *Then* email KurtS2@gmail for help.
105581 Posts in 12330 Topics by 4753 Members
Latest Member: stpatrick
* Home Help Search Login Register
  Show Posts
Pages: 1 [2] 3 4 ... 7
16  Camaro Research Group Discussion / General Discussion / headlight washer t valve on: December 30, 2011, 11:32:32 AM
Anyone out there that is selling or reproducing the headlight washer t valve for the 69 camaro rs HuhHuh?
17  Camaro Research Group Discussion / General Discussion / windshield molding on: December 19, 2011, 08:15:04 AM
hello everyone,
does anybody have any advice as to who makes a windshield molding kit that actually fits? i know that having the originals would be best but can't afford that luxury. i had purchased a set from Heartbeat City and as advertised original thickness, excellent fit, technically correct, the fit is horrible. i thought if the part was a licensed gm restoration part it would have to meet certain requirements, guess i was wrong. the top and sides will not lay flat on the glass withuout glueing them down (i would be scared the wind would blow them off) the bottom molding where it joins the a pillar and side molding is so far off the glass i can get my pinky finger behind it.
is this a common problem with these moldings or is it just me? 

thanks,
mike
18  Camaro Research Group Discussion / Restoration / rosewood wheel on: November 23, 2011, 08:33:49 AM
Has anyone had a crack  repaired in a rosewood steering wheel and been satisfied with the results?? If so i am looking for recomendations for someone that i can depend on to repair one.

Thanks,
Mike 
19  Camaro Research Group Discussion / Restoration / ride height ? on: November 05, 2011, 04:03:24 PM
i just installed a pair of Eaton leaf springs (5 leaf) under my 69 camaro with a 396 ci engine, i was told these springs would give me the correct ride height. i have not tightened any of the shackle bolts and have placed 230 pounds in the trunk which should more than exceed the weight of a tank of gas, spare tire, jack, tail pipes etc. measuring from the top of the axle tube to the bottom of the frame rail measures  8.25 inches.
what have i done wrong? any suggestions?

mike
20  Camaro Research Group Discussion / Originality / Re: black tail panel on: September 02, 2011, 07:08:34 AM
Thank You

Mike
21  Camaro Research Group Discussion / Originality / Re: black tail panel on: September 02, 2011, 05:34:26 AM
mark,
was your car original?

mike
22  Camaro Research Group Discussion / Originality / black tail panel on: September 01, 2011, 12:14:39 PM
i have read a lot of post on the blacked out tail panel on 396 cars, but none have given me the info i am requesting today. it's not about what shade of black. i have a 69 camaro and its been quite a while since i have seen it in its original colors. the painter nor myself can remember where the paint line that seperates the black from the body color behind the rear bumper is located. a picture would be great, but i will take what i can get.

mike
23  Camaro Research Group Discussion / Originality / Re: hamill seat belt on: August 29, 2011, 06:53:58 AM
Thank You,  Thats exactly what i needed to know.

Mike
24  Camaro Research Group Discussion / Originality / Re: hamill seat belt on: August 27, 2011, 07:45:39 PM
thanks paul, do they fold the opposite way on the clip end or the same (towards the headliner)? my car is a 69 also, think they are the same?


mike
25  Camaro Research Group Discussion / Originality / hamill seat belt on: August 26, 2011, 05:04:32 PM
i am presently having my seat belts restored, but i have a question about the shoulder belts and am asking for some help. my car only came with one shoulder belt and i am not sure if the fold on the belt (at the anchor that fastens to the roof) is the same on the left and right, or are they opposite? anyone have a good picture of this ?

thanks
mike
26  Camaro Research Group Discussion / Restoration / seat belt tags on: May 16, 2011, 01:52:15 PM
 Is there antone on the east coast rather than Texas that can replace seat belt tags and do a quality job?Huh



Thanks
27  Camaro Research Group Discussion / Restoration / Re: gas tank coating on: April 25, 2011, 07:05:27 AM
Thanks, i will check them both.

Mike
28  Camaro Research Group Discussion / Restoration / Re: gas tank coating on: April 24, 2011, 06:39:08 AM
where can a Ni-Terne treated steel tank be purchased? i asked what the tank i have was made of or treated with and was told it was made of steel and they did not know about the ni-terne.



Thanks,
Mike
29  Camaro Research Group Discussion / Restoration / Re: gas tank coating on: April 17, 2011, 07:31:53 PM
the tank came from heartbeat city, don't recall any spec sheet on the tank.
30  Camaro Research Group Discussion / Decoding/Numbers / Re: c code on a 69? on: April 17, 2011, 07:28:45 PM
yes, i did mean the rear axle code, sorry just was not thinking as usual. thanks!!
Pages: 1 [2] 3 4 ... 7
Powered by MySQL Powered by PHP Powered by SMF 1.1.19 | SMF © 2013, Simple Machines Valid XHTML 1.0! Valid CSS!
Page created in 0.078 seconds with 18 queries.