Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - rodent

Pages: [1] 2 3 ... 5
Well I know each guys car is his castle, but without sounding to up-ity, these were not necessarily considered rare collectibles.

I'm not sure "rare or collectible" come's into it, they're someones pride and joy that's been stolen. You comments come across as a bit flippant.

Maintenance / Re: Posi additive in Australia
« on: February 25, 2019, 03:53:23 PM »
Autobarn, Burson, Repco and a lot of other smaller retailers stock it.

General Discussion / Re: 68 Z28 on BaT
« on: February 16, 2019, 07:20:05 AM »
I just removed a bunch of posts. It was not relevant to the topic and just rehashed an old topic.

You're a good man Kurt, Jerry would be proud :)

Here is another example to compare to the one above for me both look genuine Jerry.

General Discussion / Re: 68 Z28 on BaT
« on: February 14, 2019, 07:02:31 AM »
I've got(not sure I still have it) one of those, not worth the paper it's printed on.

General Discussion / Re: rebuilt engin startup
« on: November 27, 2018, 08:08:47 AM »

Maintenance / Re: mystery oil leak
« on: November 27, 2018, 08:08:25 AM »
What transpired?

Maintenance / Re: mystery oil leak
« on: November 07, 2018, 05:49:36 PM »
Are the intake bolts that thread into the valve area sealed?

From the front of the engine:

Drivers side: 1st, 5th, 7th
Pass side: 2nd, 4th, 8th

All of these bolts are open into the inside of the engine, and if not sealed oil will creep through them.

General Discussion / Re: rebuilt engin startup
« on: September 23, 2018, 07:36:54 AM »
How did you get on with the startup?

General Discussion / Re: rebuilt engin startup
« on: September 08, 2018, 06:39:00 PM »
If you're running dual or triple valve springs, pull the inners out and reinstall after run in.

Mild Modifications / Re: Tri-Power 427 fit under 69 SS hood?
« on: July 25, 2017, 08:22:03 AM »
Do your own homework.......but I believe '67 intakes are lower than the later years. Might get you where you need to be.

General Discussion / Re: 427/425
« on: December 09, 2016, 06:44:32 AM »
Thanks for all the input and info about this car, i could share more about it but one of the members here went out of his way to locate it in an attempt to purchase even though i had interest in it. I learned from this that i should  not  be so revealing with the info about future finds. In the event that i wind up with it i plan to do a simple restoring just because i think it would be cool to have.

Give the Slippery Gypsy up.

1968 - Orphans / Re: 8L316937 - Z28 Engine Block
« on: October 08, 2016, 09:22:37 PM »
That's a lovely stamp, guy who did mine must have been drinking heavily  ;D

Originality / Re: Fill & Drain Plugs 1969 Muncie M22
« on: March 06, 2016, 07:24:40 AM »
I have one to give away, how do you work out who you give it to????

Not sure if it's for a '69 though  :-\

Decoding/Numbers / Re: vin vs engine assembly date
« on: August 22, 2015, 11:10:13 PM »
Not that's it of any help Pete, my 05a block has a casting date of April 24.

General Discussion / Re: 1111467 distributor
« on: January 25, 2015, 09:47:41 PM »
OP, isn't your car a March or April build  ??? Why would you be looking at a June Distributor  ???

Pages: [1] 2 3 ... 5