46
Originality / Re: RPO Z87
« on: July 15, 2015, 11:04:47 PM »
I got the correct hood insulation retainers a few years ago from classic industries,dont know if they still have them.
News:
Welcome to the CRG Discussion Forum!
Classified ads are not allowed on the forum.
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
47
Restoration / Re: Inner Fender Installation
« on: July 15, 2015, 10:56:26 PM »
If you are concerned about rear fender,front door damage I usually use small rubber hose 5/16 or so,cut it down the center & wrap it around those edges. It will stay in place while installing of removing fenders.
48
Originality / Re: wheel well molding bolt finish. any survivors?
« on: May 29, 2015, 10:55:44 PM »
69 O4C Norwood shiney finish
49
General Discussion / Re: 1969 Chevrolet Camaro Z-10 RS/SS 396 4bbl
« on: May 19, 2015, 11:35:56 PM »
Maybe 4E 
?
?
50
General Discussion / Re: 1969 Chevrolet Camaro Z-10 RS/SS 396 4bbl
« on: May 19, 2015, 11:32:40 PM »
That is what I have always seen 400-500.Thanks
51
General Discussion / Re: 1969 Chevrolet Camaro Z-10 RS/SS 396 4bbl
« on: May 18, 2015, 11:03:59 PM »
If Chevrolet does not know how do they know? Unless they are talking about"known examples only in their registry"??
52
General Discussion / Re: 1969 Chevrolet Camaro Z-10 RS/SS 396 4bbl
« on: May 17, 2015, 10:55:37 PM »
One of 200 produced?? One of 12 396/350 how does he know that???
One of 12 396/350 how does he know that???
53
Restoration / Re: 69 camaro dash pad peeling
« on: April 07, 2015, 11:04:03 PM »
About 5 trs ago I took my dash to a guy in town.He trimed about 1/4 inch off of the shell & then pulled the shrunken padding back around the shell. He then glued the padding back on,seemed to work pretty well.
54
General Discussion / Re: Where have all the RS SS's gone ?
« on: March 15, 2015, 10:51:27 PM »
Well as someone once told me its alot more fun for you to sell them now, rather than your relatives selling them later! 
55
Originality / Re: 69 Wheel opening mouldings
« on: January 30, 2015, 11:32:12 PM »Rear wheel well moldings have small holes for the attaching screws. The screws should be included.I believe there should be 2 screws for the front fender extension
The fronts did not need screws due to the large fender bolts holding them in place.
56
General Discussion / Re: IS THIS ANOTHER MILLION DOLLAR 6 BANGER ?
« on: December 12, 2014, 10:41:07 PM »
Ive never been on the Yenko site,thats above my pay grade 
57
General Discussion / Re: IS THIS ANOTHER MILLION DOLLAR 6 BANGER ?
« on: December 09, 2014, 12:04:40 AM »
$ 400-500 to find original valve stem caps?? People have lost their minds over these cars,
58
Originality / Re: Who makes most accurate Spark Plug Wire sets? Also heartbeats transveres Muffler
« on: November 19, 2014, 11:42:45 PM »
Steve I believe Gardner will only sell complete exhaust systems & not parts.
59
Restoration / Re: Final adjustment on RS Headlight doors
« on: August 07, 2014, 11:09:25 PM »
Your welcome!
60
Restoration / Re: Final adjustment on RS Headlight doors
« on: August 06, 2014, 12:19:01 AM »
12-4 Fig. 3 "Headlamp Panel Adjustment"