Messages

61

Restoration / GM exhaust pipe sealer substitute

« on: March 29, 2009, 11:06:46 PM »

I'm installing a new stock exhaust system in my 67 SS350 restoration project I've been working on.  I see that the AIM calls for a grease based sealer PN 9985020 at the pipe joints.  Could someone tell me a good substitute for that?  Thanks.

62

Restoration / Re: 67 roof drip rail molding install

« on: March 07, 2009, 01:00:53 AM »

I asked that last question before looking at the link Chris posted.  That other thread pretty much answers my question.  Thanks.

63

Restoration / Re: 67 roof drip rail molding install

« on: March 07, 2009, 12:54:47 AM »

Thanks Chris and Jerry.  You've both been very helpful.

It's been an awful long time since I removed the old vinyl top but I vaguely remember that there were some clips that popped in over the vinyl into the top edge of the drip rail to help hold the vinyl in place.  Is that correct or an I imagining things?  It's only been about 30 years since I stripped the old top off so my memory isn't too good on this.

Thanks again.

64

Restoration / Re: 67 roof drip rail molding install

« on: March 05, 2009, 04:36:59 PM »

Where's Jerry when you need him?  Somebody must have put these things on.

65

Restoration / 67 roof drip rail molding install

« on: March 01, 2009, 10:39:34 PM »

I'm installing a new set of drip rail moldings on my 67.  I hear they're a tight fit anyway, but mine has a new vinyl top which makes it even worse.  Does anyone have any experience with this that can describe how to do it without damaging the moldings?  Thanks.

66

Originality / Re: 67 SS350 carb spring

« on: February 02, 2009, 12:24:03 AM »

I saw the setup from the picture in the AIM but not the one you're talking about.  I'll check that out when I get home. 

67

Originality / Re: 67 SS350 carb spring

« on: February 01, 2009, 01:17:08 PM »

This is the only picture I could find that shows the setup that's in the assembly manual.  I have no way of knowing if this is how this particular car was set up originally.

68

Originality / Re: 67 SS350 carb spring

« on: February 01, 2009, 02:30:35 AM »

Thanks.  That helps a lot.  That looks like the spring I have.  The assembly manual showed it connecting by the coil which would not work with that spring.

69

Originality / Re: 67 SS350 carb spring

« on: January 31, 2009, 12:30:05 PM »

Thanks Paul.  I saw the diagram but it doesn't add up based on the spring that I have that's supposed to be the right one.  I'd still like to see a picture of a stock setup.

70

Originality / Re: 67 SS350 carb spring

« on: January 29, 2009, 11:37:11 PM »

I have a copy but didn't see this in there.  I'll try again.

71

Originality / 67 SS350 carb spring

« on: January 29, 2009, 06:53:10 PM »

Could someone please post a picture or diagram, or direct me to one, that shows the correct carb return spring setup for the 67 SS 350.  Thanks.

72

Originality / Re: 67 Muncie shifter installation

« on: January 25, 2009, 04:54:23 PM »

Yes it is.  Thanks.

73

Originality / 67 Muncie shifter installation

« on: January 25, 2009, 03:17:15 PM »

Could someone direct me to a diagram showing the installation of the Muncie shifter on a 67 Camaro?  My car hasn't had one since I got it back in 1975.  I have a new shifter and hardware kit which, of course, does not come with a diagram.

Thanks.



67 Marina Blue RS/SS 350 4 speed, black stripes and vinyl top.