16
General Discussion / Re: what intake gasket for a 69 Z? with or with out heatriser hole
« on: March 06, 2010, 11:05:48 PM »
do you remember what gasket you used
Rich
Rich
News:
Welcome to the CRG Discussion Forum!
Classified ads are not allowed on the forum.
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
17
General Discussion / what intake gasket for a 69 Z? with or with out heatriser hole
« on: March 06, 2010, 10:34:10 PM »
Im ready to put the manifold on. should I buy a gasket that has no heatriser provisions.I live in California so a choke wont be an issuse.which gasket shold I use?
Richard
Richard
18
General Discussion / who has original type rivited upper ball joints
« on: March 03, 2010, 05:58:54 AM »
same as above
Rich
Rich
19
General Discussion / how many miles are ball joints good for? who sells original type
« on: February 26, 2010, 04:56:31 AM »
Im thinking about about freshing up the frront but Im wondering if I really need to change the ball joints.If I change them,who has original looking parts.and no overseas junk.
Richard
Richard
20
General Discussion / can I use a 10105117 head gasket on block that hasnt been decked
« on: February 23, 2010, 06:22:13 AM »
my heads are fresh and have been surfaced but the deck of the block hasent.will these head gaskets work
Richard
Richard
21
General Discussion / Re: where can I get a coil bracket 4 a cowl hooded Z
« on: February 20, 2010, 08:38:00 PM »
does anyone have a picture to show the difference of both versions
Richard
Richard
22
General Discussion / where can I get a coil bracket 4 a cowl hooded Z
« on: February 19, 2010, 10:13:21 PM »
Does anyone sell a correct coil bracket for a car with the cowl hood
thanks again Richard
thanks again Richard
23
General Discussion / what engine bearings and piston rings for a 69 302 Z motor?
« on: February 18, 2010, 06:52:22 AM »
Im about to reassemble my 302 engine but what did Chevy use when these cars were built? Im sure JonhZ or someone will know.
thanks again Richard
thanks again Richard
24
General Discussion / what brand suspension parts did GM use?
« on: November 20, 2009, 10:56:55 PM »
thinking about freshening up the front end.but what brand did GM use? MOOG,TRW, ect.
Rich
Rich
25
General Discussion / AC DELCO replacement clutch #381146,is this good in a 69 Z
« on: October 20, 2009, 06:12:41 AM »
I saw that heartbeat city is selling AC DELCO clutchs for 69 Z28s.are they good enough or should I be looking at a Zoom .
Rich
Rich
26
General Discussion / Re: 69Z with 186 heads and 1.94 intake seats ????????????
« on: August 04, 2009, 07:19:11 PM »Were the intake valve areas of the combustion chambers machined around the valve pocket?Jerry,they are just like Johns pic.I wish I took some pics befor he finished the heads
Jerry
27
General Discussion / Re: 69Z with 186 heads and 1.94 intake seats ????????????
« on: August 04, 2009, 07:15:56 PM »What type of head gaskets were on it? Joe
it still had the steel shim
Rich
28
General Discussion / 69Z with 186 heads and 1.94 intake seats ????????????
« on: August 04, 2009, 06:07:09 AM »
I tore my orginal DZ motor apart and 
The guy doing my heads called and told me I had to come and check this out. This is the first time the motor has been apart so here gos.the heads are 186 castings,1.94 intake seats and 1.60 exhaust seats.strange,its gets worse.the combustion chambers are for 2.02 valves,now the kicker,it has 2.02 and 1.60 valves in the head?If I didnt see it for myself I would never believe it.could GM have screwed up when they built the engine?
Richard
The guy doing my heads called and told me I had to come and check this out. This is the first time the motor has been apart so here gos.the heads are 186 castings,1.94 intake seats and 1.60 exhaust seats.strange,its gets worse.the combustion chambers are for 2.02 valves,now the kicker,it has 2.02 and 1.60 valves in the head?If I didnt see it for myself I would never believe it.could GM have screwed up when they built the engine? Richard
29
General Discussion / Re: headers or manifolds on my 69 Z28?????
« on: July 20, 2009, 11:27:23 PM »
thanks John.maybe JohnZ or Jery will give ther opinion also.I had headers on the car when I bought it.It sure sounded cool but,Im thinking 14 years latter.maybe stock manifolds might be the the way to go.
Richard
Richard
30
General Discussion / headers or manifolds on my 69 Z28?????
« on: July 20, 2009, 09:32:44 PM »
The new engine should be done in the next couple of weeks and Im wondering if I should put the stock exhaust manifolds back on or a set of headers? 
thanks Richard
thanks Richard