CRG Discussion Forum
Welcome, Guest. Please login or register.
Did you miss your activation email?
April 16, 2014, 02:08:37 PM

Login with username, password and session length
Search:     Advanced search
Welcome to the CRG Discussion Forum!
Forum registration problems: Make sure you enter your email correctly and you check your spam box first. *Then* email KurtS2@gmail for help.
97088 Posts in 11682 Topics by 4578 Members
Latest Member: ronhill
* Home Help Search Login Register
  Show Posts
Pages: 1 ... 33 34 [35] 36 37 ... 43
511  Camaro Research Group Discussion / Restoration / Re: Correct steering box finish on: December 23, 2010, 11:38:40 PM
 I have used Martin Senour TECnique Iron Cast #7250.  I forget who suggested it, but I believe it was on here.  Works great, looks great, it is a flat or semi-gloss finish so it's not too glossy.  It's available at NAPA in a big 15 oz. spray can for 'I believe' about $8.99.  FYI - the top cover, and the round disc in the end should remain natural aluminum color.
512  Camaro Research Group Discussion / Restoration / Re: Advice on interior Restoration on: December 23, 2010, 03:05:26 AM
  I am replacing my Door Panels and rear Side Panels, corners and edges are curled and loose.  But the Trim pieces are all good.  It looks as if the trim was laminated to the Vinyl at the factory.  What would be a good strong glue to glue these on?   Would headliner glue work?
513  Camaro Research Group Discussion / Decoding/Numbers / Re: 67-68-69 hoods on: December 15, 2010, 11:06:47 PM
phil_  What was the build week of your car?  The 2 digit code on the hood is build week.  From what I have found, the body panel date code should be 1 to 3 weeks before the car build date.  The link above hood build date is week 43, my car is an 11 A (66) build date and as near as I can figure that is week 45.  All body panel date codes I have found are 42 to 44.
514  Camaro Research Group Discussion / Originality / Re: 68 396 radiator cap on: December 15, 2010, 02:02:58 AM
  Can someone post a pic. of a correct RC 15 Radiator cap?  As stated earlier on this post I am seeing many different versions.  I'm assuming a correct cap should #1 be stainless, and #2 have Big ears.  Should it have raised letters"NEVER OPEN HOT" or recess stamped letters "TURN TIGHT" and "REMOVE SLOWLY"?   I am even seeing caps claiming to be NOS both ways.  What is correct?
515  Camaro Research Group Discussion / Decoding/Numbers / Re: 67-68-69 hoods on: December 15, 2010, 01:30:17 AM
Go to this link for picture of hood date code;
http://www.camaros.org/forum/index.php?topic=6696.0
516  Camaro Research Group Discussion / General Discussion / Re: RECORD BREAKING YEAR FOR CHP on: December 03, 2010, 01:44:38 AM
Congrats Jerry, it's amazing what you've done with that car in a relatively short time.  Great photo History.  Best of luck on continuing this reign.
517  Camaro Research Group Discussion / Originality / Re: '67-'68-'69 Camaro HEADER Panel on: December 03, 2010, 01:05:11 AM
binky3>  Date codes are 2 digit for the week of the year.  ie; 46 would be week 46, probably mid November.  Panel date codes are usually 2 to 4 weeks prior to build date of car. 

RonM>  I would say look a little closer, your Date should possibly be 26.  The 2 might not be as visible for some reason.
518  Camaro Research Group Discussion / Originality / Re: Correct Window Molding clips on: November 12, 2010, 12:01:52 AM
Thanks!!! jeff
519  Camaro Research Group Discussion / Originality / Re: Correct Window Molding clips on: November 10, 2010, 01:43:35 AM
jeff g>  Would these be the correct clips?   Longer Reddish - Front, Narrower Gray - Rear??
520  Camaro Research Group Discussion / Originality / Re: Any Interest in Original Type Door Watershields? on: November 06, 2010, 12:14:03 AM
I would still be interested in a standard '67 set also.
521  Camaro Research Group Discussion / Originality / Re: Date code on '67 Steering Gear box on: November 06, 2010, 12:12:30 AM
rskev> The box was painted black over rust, so I started with Zip Strip paint remover.  Then several times of spraying on Muratic acid, followed by Krud Kutter , a Must for Rust, rust remover.  The nice thing about the Krud Kutter, a Must for Rust, is you don't rinse it off.  Allow it to Sun dry or wipe it dry with old rags, it leaves some kind of coating that inhibits the part from quickly surface rusting again.  It can be wire brushed and painted over.  I intend to paint the box with Cast Blast, the box is supposed to be natural cast finish.  The top cover (Aluminum), and the round front cover also (Aluminum) should be left natural.
522  Camaro Research Group Discussion / Originality / Re: Date code on '67 Steering Gear box on: November 03, 2010, 09:00:43 PM
  Thanks Guys!!!!!!!!!!!
523  Camaro Research Group Discussion / Originality / Correct Window Molding clips on: November 03, 2010, 02:31:40 PM
  I have an early build (11A - 66) '67 Coupe no Vinyl Roof.  I am trying to find out what are the "correct" Windshield side and upper molding clips.  Also "correct" Rear Window molding clips.  Anybody have part #'s ?   I'm seeing different ones offered, and they don't coorespond with what is on the car.  Maybe they have been changed.
524  Camaro Research Group Discussion / Decoding/Numbers / Re: Q-Jet Date Codes on: November 02, 2010, 11:09:29 PM
I am also looking at a couple of #7029202 DH carbs. ,  the date supposedly is on the base plate.  One is 032   2,  the other is 2   22G.  I'm assuming the first is julian date 032 or 1 st. of Feb., what's the extra 2?   The second I'm assuming the date 22G is the 22 nd. of July, again, what's that first 2 for?  Thanks for any help!
525  Camaro Research Group Discussion / Originality / Re: 69 rear brake drum & front rotor P/N's and date codes on: October 28, 2010, 11:48:20 PM
  Can anybody give a quick lesson on how to read these Brake Drum date codes?  ie; W-12X , W-14X , W-1X
Pages: 1 ... 33 34 [35] 36 37 ... 43
Powered by MySQL Powered by PHP Powered by SMF 1.1.19 | SMF © 2013, Simple Machines Valid XHTML 1.0! Valid CSS!
Page created in 0.099 seconds with 18 queries.