CRG Discussion Forum
Welcome, Guest. Please login or register.
Did you miss your activation email?
April 24, 2014, 02:34:05 AM

Login with username, password and session length
Search:     Advanced search
Welcome to the CRG Discussion Forum!
Forum registration problems: Make sure you enter your email correctly and you check your spam box first. *Then* email KurtS2@gmail for help.
97521 Posts in 11718 Topics by 4581 Members
Latest Member: Cooper48
* Home Help Search Login Register
  Show Posts
Pages: 1 2 3 [4]
46  Camaro Research Group Discussion / General Discussion / Three Holes in Frame for Clutch Z bar (Cross Shaft) Bracket, Bolt Size ? on: October 19, 2008, 02:27:23 PM
Greetings.

There are three holes in the drivers side of the '68 frame for mounting the bracket that holds the clutch cross shaft ( Z Bar, bellcrank, lever, whatever you like to call it).

These holes appear to be threaded, tapped for bolts.

Anyone know what size (diameter) bolt and weather they are coarse or fine thread?

Thanks...!
47  Camaro Research Group Discussion / Mild Modifications / Re: LocationTemplate for cutting hole in floor tunnel for Hurst shifter... on: October 11, 2008, 03:57:53 PM
Hey mel, thanks again for the reply. Hope your trip is/was to somewhere fun!

I wish I had the FAM (factory assembly manual). Sure would be neat if someone who has one could take a look and see if there is any info in the manual regarding hole size, location dimensions, etc.

I would like to keep the hole as small as possible.

I really appreciate this site and the contributors!

By the way...my real name is....

Smokey Burnout.


SeeYa !!
48  Camaro Research Group Discussion / Mild Modifications / Re: LocationTemplate for cutting hole in floor tunnel for Hurst shifter... on: October 06, 2008, 09:50:01 AM
Hey mel, thanks for the pic, I appreciate it.

If possible, if the floor hole is still accessible,  could you lay a ruler or tape measure next to the hole, with the ruler's starting "0" end at the floor crease just ahead of the hole, and take another pic for hole size and location? This would help me in prepping for my car's "surgery".   

Do you (or anyone) know if this looks like a hole that was cut at the factory?

Thanks again!

 
49  Camaro Research Group Discussion / General Discussion / Re: Hurst Competition Plus body number 2479.... and correct arm... on: September 25, 2008, 07:50:50 AM
Hey Joe...thanks for the info on the Hurst shifter stick 5325. My application will be for a '68 Camaro with console.

Just to confirm, the 5325 is a bayonet type, not the bolt on type, correct?

Also, is it the round style or the flat sided type?

Do you know where or who might have the 5325 stick available for purchase?

Thanks again.
50  Camaro Research Group Discussion / General Discussion / Hurst Competition Plus body number 2479.... and correct arm... on: September 24, 2008, 06:24:22 PM
Hey, anybody know what car would use a Hurst Competition Plus shifter body number 2479?
Also, what is the correct Hurst  number for a bayonet type shifter arm for the '69 Camaro w/ console?

Thank you!
 
51  Camaro Research Group Discussion / Mild Modifications / LocationTemplate for cutting hole in floor tunnel for Hurst shifter... on: September 24, 2008, 05:00:38 PM
Greetings to all. I am in the process of preparing to install a Muncie M20 and Hurst shifter in my '68 Camaro which currently has the PowerGlide automatic. I have heard that there may be a template available to properly mark the hole location for the floor tunnel opening for the shifter. I assume this would be a paper or card stock template placed on the floor to identify proper locating of the hole prior to cutting.

Has anyone seen this template or know of where to obtain one ??

Thank you !!

 
Pages: 1 2 3 [4]
Powered by MySQL Powered by PHP Powered by SMF 1.1.19 | SMF © 2013, Simple Machines Valid XHTML 1.0! Valid CSS!
Page created in 0.089 seconds with 18 queries.