CRG Discussion Forum
Welcome, Guest. Please login or register.
Did you miss your activation email?
April 23, 2014, 04:31:51 AM

Login with username, password and session length
Search:     Advanced search
Welcome to the CRG Discussion Forum!
Forum registration problems: Make sure you enter your email correctly and you check your spam box first. *Then* email KurtS2@gmail for help.
97443 Posts in 11712 Topics by 4581 Members
Latest Member: Cooper48
* Home Help Search Login Register
  Show Posts
Pages: [1] 2 3
1  Camaro Research Group Discussion / General Discussion / Re: Tire sice on a 1967 RS on: Today at 03:49:02 AM
I'm not trying to pick apart your spelling, just trying to help.

LOL - spelling is not my strength - not even in Danish, so thanks ;-)
2  Camaro Research Group Discussion / General Discussion / Re: Need help with 1967 RS headlights on: April 22, 2014, 02:59:25 PM
Hmm not sure I understand - sorry :-((

If the motor does not operate if I connect the wires to he batteri in any way - the motor is broken, right ??
3  Camaro Research Group Discussion / General Discussion / Re: Tire sice on a 1967 RS on: April 22, 2014, 02:57:11 PM
Need input please....

What backspace and tire sice are you running on 15X6 and 15X7 Rally wheels front and/or back ??
4  Camaro Research Group Discussion / General Discussion / Re: Need help with 1967 RS headlights on: April 22, 2014, 01:50:47 PM
Thanks guys ;-)

IŽll forward the link to work tomorrow and print it out - and then try to read AND understand it with my dictinary ;-)

Before I saw this I took out the hole doorpiece ( it didnt work any way at all ) - I dont think I can messyre anything in the wire harness going til the motor. I can test the 2 limit switches, and they work fine.

If I put the 2 wires to the batteri - should the door move if the motor is okey ??

Regards
Claus, Denmark
5  Camaro Research Group Discussion / General Discussion / Re: Need help with 1967 RS headlights on: April 21, 2014, 04:05:55 PM
Do you have an OHM meter ?  Or 12V test light ?

I'm at work today ,can email you copies of the 67 instruction/troubleshooting guide tomorrow. Only problem I ever had was one of the motors went bad when the car was about 22 years old.

Yes I have both.

They didnt work any way - IŽll try to locate the motor and limit switches tomorrow - but the guide would be great, thanks ;-)

Regards
claus@bankmand.com
6  Camaro Research Group Discussion / General Discussion / Need help with 1967 RS headlights on: April 21, 2014, 11:27:59 AM
Hi

My right headligt door is not workring - and I need to find out where the problem is - hope somebody can explane what to do and how to do ?!?! ;-)

I could open and close the door by hand - so I have removed the cover and plate.

I have the 1967-69 Restauration guide and on page 58 there is a drawing where I can see the inboard and outboard limit switch and the motor etc.

How do I check where the malfuncion is ??

Thanks for any help
/Claus
7  Camaro Research Group Discussion / General Discussion / Tire sice on a 1967 RS on: April 15, 2014, 05:28:49 PM
Hi

What is the max tire sice I can have on the front and rear without rubbing against something ?

I have 15x7 Rally wheels and standard suspension with 4 drums

Thanks / Claus
8  Camaro Research Group Discussion / General Discussion / Re: Neutral switch - that could have gone so wrong :-( on: July 12, 2013, 04:35:58 AM
Thanks - IŽll try
9  Camaro Research Group Discussion / General Discussion / Neutral switch - that could have gone so wrong :-( on: July 11, 2013, 10:26:31 AM
yesterday I discovered the bad way that my neutral swith do not work :-(( Fortunately I steped on the brakes before it ran over my harley and further into the garage :-((

it is a 1967 Camaro - I cant se any problems with the wires to the gearlever ?!?!

Any help with truble shooting would be great - thanks.

/Claus, Denmark
10  Camaro Research Group Discussion / General Discussion / 1967 Camaro Generator bracket - what to do ?? on: July 01, 2013, 04:23:15 AM
Hi

I have put on som shiny valvecovers that are a little bit taller than the original ones, - because of that the generator fan belt had to be chanced to one 1" longer but now my generator tighten bracket os not long enough so I can tighten the fan belt :-((

My info is:

* 327 engine without bolt holes in the head
* Short water pump
* Original cast iron exhaust manifolds that hold the lower generator bracket

What have you guys done? hope to get som helping info ;-)

/Claus, Denmark
11  Camaro Research Group Discussion / General Discussion / Re: Yes... my first V8 rebuild ;-) on: June 27, 2013, 12:50:21 AM
Pretty much std 327.

Has the sum1102 cam, 600 Holley, powerglide tranny
12  Camaro Research Group Discussion / General Discussion / Wirelook in a 1967 RS on: June 26, 2013, 04:55:32 AM
I am very quirus how you guys have routed all your wires and spark ploug wires in your enginebay.

Any pics would be great - thanks ;-)

Regards
Claus, Denmark
13  Camaro Research Group Discussion / General Discussion / Yes... my first V8 rebuild ;-) on: June 26, 2013, 04:52:55 AM
Hi.

YES... IT lookes like I did it. My first ever complete 327 V8 rebuild ;-)

I must admit I have had butterflies in the stumag for a few weeks now, and yeasterday after I had been checking everything over and over again I turned the key - and wromm wromm..

I ran it over 2000 RPM for about 20-22 minuts in different RPM.

I put the timing on 8 degrees to begin with, disconected the vacum to the distributor ( original with points )

Then turned the RPM up til 4000 and the timing was 42 degrees.

My book says timing at 4000 should be around 34-38 isnŽt that right??

What should my idle RPM be?
How much should it drop when put in gear?
How much should my idle timing be?

I put in a bottle of came brake in doze in the oil - when should I change the oil ? ( the cylinder was only honed and new rings )

Thanks for your input ;-)

Regards
Claus, Denmark
14  Camaro Research Group Discussion / General Discussion / Re: Problem with tranny deepstick on: June 26, 2013, 12:44:09 AM
Thanks - I found one a few days ago - so everything is fine no ;-)
15  Camaro Research Group Discussion / General Discussion / Re: Wiering diagram for a 1967 RS.. on: June 24, 2013, 07:24:02 AM
OKI - Thanks..

I have printed the 7-8 color wierings diagrams - looks great....

/Claus
Pages: [1] 2 3
Powered by MySQL Powered by PHP Powered by SMF 1.1.19 | SMF © 2013, Simple Machines Valid XHTML 1.0! Valid CSS!
Page created in 0.08 seconds with 18 queries.