Messages

31

General Discussion / Re: Need help with 1967 RS headlights

« on: April 21, 2014, 09:05:55 PM »

Do you have an OHM meter ?  Or 12V test light ?

I'm at work today ,can email you copies of the 67 instruction/troubleshooting guide tomorrow. Only problem I ever had was one of the motors went bad when the car was about 22 years old.

Yes I have both.

They didnt work any way - I´ll try to locate the motor and limit switches tomorrow - but the guide would be great, thanks ;-)

Regards
claus@bankmand.com

32

General Discussion / Need help with 1967 RS headlights

« on: April 21, 2014, 04:27:59 PM »

Hi

My right headligt door is not workring - and I need to find out where the problem is - hope somebody can explane what to do and how to do ?!?! ;-)

I could open and close the door by hand - so I have removed the cover and plate.

I have the 1967-69 Restauration guide and on page 58 there is a drawing where I can see the inboard and outboard limit switch and the motor etc.

How do I check where the malfuncion is ??

Thanks for any help
/Claus

33

General Discussion / Tire sice on a 1967 RS

« on: April 15, 2014, 10:28:49 PM »

Hi

What is the max tire sice I can have on the front and rear without rubbing against something ?

I have 15x7 Rally wheels and standard suspension with 4 drums

Thanks / Claus

34

General Discussion / Re: Neutral switch - that could have gone so wrong :-(

« on: July 12, 2013, 09:35:58 AM »

Thanks - I´ll try

35

General Discussion / Neutral switch - that could have gone so wrong :-(

« on: July 11, 2013, 03:26:31 PM »

yesterday I discovered the bad way that my neutral swith do not work :-(( Fortunately I steped on the brakes before it ran over my harley and further into the garage :-((

it is a 1967 Camaro - I cant se any problems with the wires to the gearlever ?!?!

Any help with truble shooting would be great - thanks.

/Claus, Denmark

36

General Discussion / 1967 Camaro Generator bracket - what to do ??

« on: July 01, 2013, 09:23:15 AM »

Hi

I have put on som shiny valvecovers that are a little bit taller than the original ones, - because of that the generator fan belt had to be chanced to one 1" longer but now my generator tighten bracket os not long enough so I can tighten the fan belt :-((

My info is:

* 327 engine without bolt holes in the head
* Short water pump
* Original cast iron exhaust manifolds that hold the lower generator bracket

What have you guys done? hope to get som helping info ;-)

/Claus, Denmark

37

General Discussion / Re: Yes... my first V8 rebuild ;-)

« on: June 27, 2013, 05:50:21 AM »

Pretty much std 327.

Has the sum1102 cam, 600 Holley, powerglide tranny

38

General Discussion / Wirelook in a 1967 RS

« on: June 26, 2013, 09:55:32 AM »

I am very quirus how you guys have routed all your wires and spark ploug wires in your enginebay.

Any pics would be great - thanks ;-)

Regards
Claus, Denmark

39

General Discussion / Yes... my first V8 rebuild ;-)

« on: June 26, 2013, 09:52:55 AM »

Hi.

YES... IT lookes like I did it. My first ever complete 327 V8 rebuild ;-)

I must admit I have had butterflies in the stumag for a few weeks now, and yeasterday after I had been checking everything over and over again I turned the key - and wromm wromm..

I ran it over 2000 RPM for about 20-22 minuts in different RPM.

I put the timing on 8 degrees to begin with, disconected the vacum to the distributor ( original with points )

Then turned the RPM up til 4000 and the timing was 42 degrees.

My book says timing at 4000 should be around 34-38 isn´t that right??

What should my idle RPM be?
How much should it drop when put in gear?
How much should my idle timing be?

I put in a bottle of came brake in doze in the oil - when should I change the oil ? ( the cylinder was only honed and new rings )

Thanks for your input ;-)

Regards
Claus, Denmark

40

General Discussion / Re: Problem with tranny deepstick

« on: June 26, 2013, 05:44:09 AM »

Thanks - I found one a few days ago - so everything is fine no ;-)

41

General Discussion / Re: Wiering diagram for a 1967 RS..

« on: June 24, 2013, 12:24:02 PM »

OKI - Thanks..

I have printed the 7-8 color wierings diagrams - looks great....

/Claus

42

General Discussion / Re: Wiering diagram for a 1967 RS..

« on: June 24, 2013, 11:34:38 AM »

Thanks ;-)

Is that a 1. gen Camaro forum like this ??

/Claus

43

General Discussion / Wiering diagram for a 1967 RS..

« on: June 24, 2013, 08:21:21 AM »

Hi

I am so bad with wiering :-((, can someone plese help me with a link or file on a wiering diagram i colores I can print out, and bring to the garage ??

Thanks
Claus Møller, Denmark

44

General Discussion / Problem with tranny deepstick

« on: June 23, 2013, 05:29:39 PM »

Hi.

I cant get the deepstick in my ( 1967 powerglide ) tranny - perhaps the O-ring is not right ?!?!

Can anyone please tell me the correct size for the O-ring ??

Thanks
Claus Møller, Denmark

45

General Discussion / Re: pics on how the power steering pump is installed

« on: May 28, 2013, 07:33:58 AM »

Thanks guys - everything is now installed ;-)

How should the oil lines run ? under or abow the M mount? and how much slack in the lines?

Thanks
Claus